JVC UX-S57 Adjusting the Volume, Reinforcing the Bass Sound, On the remote control, On the unit

Page 14

Basic and Common Operations (continued)

Adjusting the Volume

You can adjust the volume level only while the unit is turned on. The volume level can be adjusted between “VOLUME MIN” and “VOLUME 1” – “VOLUME 40 (VOLUME MAX).”

On the remote control:

To increase the volume, press VOLUME +.

To decrease the volume, press VOLUME –.

•When you press and hold either button, you can change the volume level continuously.

VOLUME

On the unit:
To increase the volume, turn the	VOLUME
	VOLUME
VOLUME + / – control clockwise.
To decrease the volume, turn the
VOLUME + / – control counterclockwise.

Reinforcing the Bass Sound

The richness and fullness of the bass sound is clearly maintained regardless of how low you set the volume —Active Hyper Bass Pro.

• This function also affects the sound from headphones.

To get the effect, press AHB PRO repeatedly so							AHB PRO
To get the effect, press AHB PRO repeatedly so
that “AHB BASS1” or “AHB BASS2” appears on
the display.
The AHB PRO indicator also lights up on the
display.
				AHB PRO indicator


1	2	3	4	AHB PRO
1	2	3	4	5

CD

•Each time you press the button, the Active Hyper Bass Pro mode changes as follows:

For private listening

Connect a pair of headphones to the PHONES jack. No sound comes out of the speakers. Be sure to turn down the volume before connecting or putting on the headphones.

DO NOT turn off (standby) the unit with the volume set to an extremely high level; Otherwise, the

sudden blast of sound can damage your hearing, speakers and/or headphones when you turn on the unit or start playing any source.

REMEMBER you cannot adjust the volume level while the unit is in standby mode.

AHB BASS1 AHB BASS2

BASS OFF (canceled)

• “AHB BASS2” is more effective than “AHB BASS1.”

To cancel the effect, press AHB PRO repeatedly until “BASS OFF” appears on the display.

The AHB PRO indicator goes off.

11

Image 14

Contents Instructions Important for Laser Products Above ALL About This Manual PrecautionsIntroduction Contents Front panel Location of the Buttons and ControlsFront Panel Display window on the front panel Display windowRemote Control See pages in parentheses for detailsGetting Started Connecting AntennasBefore connecting it, disconnect the supplied FM antenna UnpackingAM MW antenna Connecting SpeakersRelease your finger from the clamp To connect speakers To remove the speaker grilles Connecting Other Equipment Putting the Batteries into the Remote Control To connect audio equipmentOn the remote control only Press CLOCK/TIMER Setting the ClockOn the remote control only Press Disc UP or Disc Down to adjust the minute, then pressTurning On the Power To turn off the unit automatically Auto StandbyReinforcing the Bass Sound Adjusting the VolumeOn the remote control On the unitAdjusting the Tone Changing the Display BrightnessListening to FM and AM MW Broadcasts Tuning in to a StationPresetting Stations Stored appears on the display for a while Tuning in to a Preset StationPress SET again Searching for Programs by PTY Codes PTY Search Receiving FM Stations with RDSChanging the RDS Information Wait for about 3 seconds after specifying the data type Switching Temporarily to a Program Type of Your ChoiceType you want flashes on the display To activate the Enhanced Other Networks functionPlaying Back Discs on the 5-CD Changer When playing CD-Rs or CD-RWsAbout the disc indicators Loading DiscsPlaying Back All the Entire Discs -Continuous Play To select a group or track before playback MP3 discs only To go to another track directly using the number buttonsBasic Disc Operations To locate a particular point in a track during playPrograming the Track Playing Order -Program Play Prohibiting Disc Ejection Playing at Random-Random PlayRepeating Tracks or Discs-Repeat Play CD Random appears on DisplayUsing the Timers Using the Daily TimerPlay Adjust the clock if neededPress STANDBY/ON to turn off Unit if the unit is on How the Sleep Timer actually works Using the Sleep TimerOn the remote control only Press Sleep Sleep indicator lights up on the displayTo clean the disc MaintenanceCleaning the unit Stains on the unitAction TroubleshootingSymptom Possible Cause Additional Information Description of the PTY codesSpecifications UX-S57 Micro Component System