JVC LVT1507-012A manual Basic Operations, Daily Operational Procedure Selecting the Source to Play

Page 11

Basic Operations

The following operations are commonly used when you play any sound sources.

Operations hereafter will be explained using the buttons on the front panel.

You can also use the buttons on the remote control for the same functions if they have the same and similar names/marks.

Daily Operational Procedure

Selecting the Source to Play

English

1Turn on the power.

•See “Turning On the Power” below.

2Select the source.

•See “Selecting the Source to Play” to the right.

3Adjust the volume.

•See “Adjusting the Volume” on page 10.

4Select the Surround or DSP modes.

•See “Activating the Surround Modes” (page 25) and “Activating the DSP Modes” (page 27).

Turning On the Power

Press STANDBY/ON (or STANDBY/ON AUDIO on the remote control).

The STANDBY lamp goes off.

Current source name appears.

VOLUME

Current volume level appears.

To turn off the power (into standby mode),

press STANDBY/ON (or STANDBY/ON AUDIO on the remote control) again.

The STANDBY lamp lights up.

Note:

A small amount of power is consumed in standby mode. To turn off

the power completely, unplug the AC power cord.

When you have connected digital source components using the digital terminals, first change the input mode for these components to the digital input mode (see page 11).

Press one of the source selection buttons.

Selected source name appears.

VOLUME

AUX	DVD	VCR	TV SOUND		CD	TAPE/CDR	FM	AM
						SOURCE NAME
			On the front panel
		TAPE/CDR		CD	DVD	AUX
			FM/AM	TV SOUND	VCR

On the remote control

Notes:

•When connecting a CD recorder to the TAPE/CDR jacks, change the source name shown on the display. For details, see page 12.

•By pressing the one of the audio source selection buttons—TAPE/ CDR, CD, and FM/AM—on the remote control, you can turn on the receiver and select the audio source.

9

Image 11

Contents LVT1507-012A US RX-5062SEuropean Union only Table of Contents Display Parts IdentificationFront Panel Rear Panel Remote ControlConnecting the FM and AM Antennas Before Installation Adjusting the Voltage SelectorChecking the Supplied Accessories Putting Batteries in the Remote ControlAM Loop Antenna Connecting the Speakers and SubwooferConnecting the speakers AM antenna connectionsAnalog Connections Connecting Audio/Video ComponentsConnecting the subwoofer Placing speakersVideo camera, etc Video component connectionsDVD player Digital input terminals Connecting the Power CordPlug the power cord into an AC outlet Digital ConnectionsBasic Operations Daily Operational Procedure Selecting the Source to PlayTurning On the Power Picture from a video component such as the VCR or DVD Adjusting the VolumeWhen analog input is selected Always lights up SoundTurning On and Off Selecting the Analog or Digital Input ModeListening with headphones Press Subwoofer OUT ON/OFF to cancel the subwoofer outputChanging the Display Brightness Attenuating the Input SignalChanging the Source Name Recording a source Using the Sleep TimerBasic adjustment auto memory Muting the SoundReceiving Radio Broadcasts Setting the AM Tuner Interval SpacingTuning in to Stations Manually Using Preset TuningTo tune in a preset station Press the number buttons to select a preset channel numberSelecting the FM Reception Mode While listening to an FM station, press FM ModeChannel number Basic SettingsQuick Speaker Setup Press Quick Speaker SetupEx. When setting Virtual Surround Back to Vrtl SB on Basic Setting ItemsBasic Procedure Press SettingSetting the Bass Sounds Setting the SpeakersSetting the Speaker Distance Select the playback sounds channel Selecting the Main or Sub ChannelSet the components connected to the digital terminals Setting for Effective Surround OperationsSetting the Digital Input Terminals Select Vrtl SB on to activate Virtual Surround BackEx. When adjusting the subwoofer level to Adjusting SoundBasic Adjustment Items Press AdjustAdjusting the Speaker Output Levels Adjusting the Equalization PatternsDolby Digital 5.1CH Using the Surround ModesReproducing Theater Ambience Introducing the Surround Modes Dolby Digital*1DTS 96/24 What is Linear PCM?What is Dual Mono? DTS Digital SurroundSelect and play any source Press Surround to activate the Surround modeActivating the Surround Modes Digital Acoustic Processor DAP modes Using the DSP ModesReproducing the Sound Field Introducing the DSP ModesAll Channel Stereo To cancel the DSP modeMulti-channel digital signals Activating the DSP ModesTuner Operating JVC’s Audio/Video ComponentsOperating Audio Components Sound control section AmplifierDVD player Operating Video ComponentsCD changer Select a disc numberProblem Possible Cause Solution TroubleshootingAudio SpecificationsOutput Power AmplifierGeneral FM tuner IHFAM tuner Receiver