JVC LVT1507-012A manual Activating the Surround Modes, Select and play any source

Page 27

Activating the Surround Modes

Available Surround modes vary depending on the incoming signals.

Activating one of the Surround modes for a source automatically recalls the memorized settings and adjustments (see pages 16 to 22).

Auto Surround Function

This receiver has Auto Surround Function, which allows you to enjoy the Surround mode simply by selecting the source (with digital input selected for that source).

Auto Surround works...

•When multi-channel signal is detected, an appropriate Surround mode will be turned on.

•When Dolby Digital 2-channel with surround signals is detected, “PLII MOVIE” will be selected.

•When Dolby Digital 2-channel without surround signals or Linear PCM signal is detected, “SURROUND OFF” will be selected.

Note:

This function does not take effect in the following cases:

–While playing an analog source,

–While selecting any of DSP modes (see page 26), and

–While listening with the headphones—“HEADPHONE” or “3D H PHONE” (see pages 11 and 24).

Activating the Surround Modes Manually

1Select and play any source.

•Make sure you have selected the analog or digital input mode correctly.

2Press SURROUND to activate the Surround mode.

•When “DOLBY DIGITAL,” “DTS SURROUND,” or “DUAL MONO” is selected as the Surround mode, pressing SURROUND changes the indication on the display alternately between “AUTO SURROUND” and each Surround mode. (The surround effect does not change.)

•For Dolby Digital multi-channel digital software (except

2-channel and Dual Mono software), incoming signals are automatically detected and “DOLBY DIGITAL” is activated.

•For DTS multi-channel digital software (except 2-channel and Dual Mono software), incoming signals are automatically detected and “DTS SURROUND” is activated.

Note:

When the Dolby Digital or DTS multi-channel digital signal stops

coming in, “PLII MOVIE” will be activated.

•For analog sources and digital 2-channel software, you can select one of the following Surround modes. Each time you press SURROUND, Surround modes change as follows:

PRO LOGIC

 

 

PLII MOVIE

 

 

 

PLII MUSIC

 

 

 

 

 

 

(Dolby Pro Logic II Movie)

 

(Dolby Pro Logic II Music)

 

AUTO SURROUND*

 

 

PLII GAME

 

 

 

 

 

 

 

 

(Dolby Pro Logic II Game)

*The receiver automatically changes the Surround mode to “PLII MOVIE” or “SURROUND OFF” according to the input signal.

•For Dual Mono software, you can select the channel you listen to. (See page 19.)

DUAL MONO

To adjust the speaker output level, center tone, and sound effect of Dolby Pro Logic II Music, see page 22.

To cancel the Surround mode

Press SURROUND/DSP OFF.

When playing Dolby Digital Surround EX or DTS-ES software

You can enjoy Virtual 6.1-channel playback using Virtual Surround Back.

To activate Virtual Surround Back, see page 20.

VIRTUAL SB

SB

English

25

Page 26 Page 28
Image 27
Page 26 Page 28
Contents LVT1507-012A US RX-5062SEuropean Union only Table of Contents Parts Identification Front PanelDisplay Rear Panel Remote ControlConnecting the FM and AM Antennas Before Installation Adjusting the Voltage SelectorChecking the Supplied Accessories Putting Batteries in the Remote ControlAM Loop Antenna Connecting the Speakers and SubwooferConnecting the speakers AM antenna connectionsAnalog Connections Connecting Audio/Video ComponentsConnecting the subwoofer Placing speakersVideo component connections DVD playerVideo camera, etc Digital input terminals Connecting the Power CordPlug the power cord into an AC outlet Digital ConnectionsDaily Operational Procedure Selecting the Source to Play Turning On the PowerBasic Operations Picture from a video component such as the VCR or DVD Adjusting the VolumeWhen analog input is selected Always lights up SoundTurning On and Off Selecting the Analog or Digital Input ModeListening with headphones Press Subwoofer OUT ON/OFF to cancel the subwoofer outputAttenuating the Input Signal Changing the Source NameChanging the Display Brightness Recording a source Using the Sleep TimerBasic adjustment auto memory Muting the SoundReceiving Radio Broadcasts Setting the AM Tuner Interval SpacingTuning in to Stations Manually Using Preset TuningTo tune in a preset station Press the number buttons to select a preset channel numberSelecting the FM Reception Mode While listening to an FM station, press FM ModeChannel number Basic SettingsQuick Speaker Setup Press Quick Speaker SetupEx. When setting Virtual Surround Back to Vrtl SB on Basic Setting ItemsBasic Procedure Press SettingSetting the Speakers Setting the Speaker DistanceSetting the Bass Sounds Select the playback sounds channel Selecting the Main or Sub ChannelSet the components connected to the digital terminals Setting for Effective Surround OperationsSetting the Digital Input Terminals Select Vrtl SB on to activate Virtual Surround BackEx. When adjusting the subwoofer level to Adjusting SoundBasic Adjustment Items Press AdjustAdjusting the Speaker Output Levels Adjusting the Equalization PatternsDolby Digital 5.1CH Using the Surround ModesReproducing Theater Ambience Introducing the Surround Modes Dolby Digital*1DTS 96/24 What is Linear PCM?What is Dual Mono? DTS Digital SurroundPress Surround to activate the Surround mode Activating the Surround ModesSelect and play any source Digital Acoustic Processor DAP modes Using the DSP ModesReproducing the Sound Field Introducing the DSP ModesAll Channel Stereo To cancel the DSP modeMulti-channel digital signals Activating the DSP ModesTuner Operating JVC’s Audio/Video ComponentsOperating Audio Components Sound control section AmplifierDVD player Operating Video ComponentsCD changer Select a disc numberProblem Possible Cause Solution TroubleshootingAudio SpecificationsOutput Power AmplifierFM tuner IHF AM tunerGeneral Receiver
Top Page Image Contents