JVC LVT1507-012A manual Operating JVC’s Audio/Video Components, Operating Audio Components, Tuner

Page 30

English

Operating JVC’s Audio/Video Components

You can operate JVC’s audio and video components with this receiver’s remote control, since control signals for JVC’s components are preset in the remote control.

IMPORTANT:

To operate JVC’s audio and video components using the supplied remote control:

•When using the remote control, aim the remote control directly at the remote sensor on each component, not on the receiver.

•Refer also to the manuals supplied with your components.

•Some JVC’s VCRs can accept two types of the control signals— remote code “A” and “B.” Before using this remote control, make sure that the remote control code of the target VCR is set to code “A.”

Operating Audio Components

Sound control section (Amplifier)

You can always perform the following operations:

STANDBY/ON

AUDIO:

 

Turn on or off the receiver.

VOLUME +/–:

Adjust the volume level.

MUTING:

Turn on or off sound muting.

ANALOG/DIGITAL: Switch the analog and digital input

 

alternately.

DIMMER:

Dim or brighten the display.

SLEEP:

Set the Sleep Timer.

SURROUND:

Turn on and select Surround modes.

DSP:

Turn on and select DSP modes.

SURROUND/DSP OFF:

Turn off the Surround and DSP mode.

After pressing SOUND, you can perform the following operations by using the number buttons:

FRONT L then LEVEL +/–:Adjust the left front speaker output

level.

FRONT R then LEVEL +/–:Adjust the right front speaker output

level.

CENTER then LEVEL +/–:

Adjust the center speaker output level.

SURR L then LEVEL +/–:

Adjust the left surround speaker

 

output level.

SURR R then LEVEL +/–:

Adjust the right surround speaker

 

output level.

SUBWFR then LEVEL +/–: Adjust the subwoofer output level.

EFFECT:

Adjust the effect level.

TEST:

Turn on or off test tone output.

Note:

After adjusting sounds, press the corresponding source selection button to operate your target source by using the number buttons; otherwise, the number buttons cannot be used for operating your target source.

Tuner

You can always perform the following operations:

FM/AM: Alternate between FM and AM.

After pressing FM/AM, you can perform the following operations on a tuner:

1 – 10, +10: Select a preset channel number directly. For channel number 5, press 5.

For channel number 15, press +10, then 5. For channel number 20, press +10, then 10.

FM MODE: Change the FM reception mode.

CD player

After pressing CD, you can perform the following operations on a CD player:

3:

Start playing.

4:

Return to the beginning of the current (or previous)

 

track.

¢:

Skip to the beginning of the next track.

7:

Stop playing.

8:

Pause playing. To resume, press 3.

1 – 10, +10: Select a track number directly. For track number 5, press 5.

For track number 15, press +10, then 5. For track number 20, press +10, then 10.

For track number 30, press +10, +10, then 10.

28

Page 29 Page 31
Image 30
Page 29 Page 31
Contents RX-5062S LVT1507-012A USEuropean Union only Table of Contents Parts Identification Front PanelDisplay Remote Control Rear PanelPutting Batteries in the Remote Control Before Installation Adjusting the Voltage SelectorChecking the Supplied Accessories Connecting the FM and AM AntennasAM antenna connections Connecting the Speakers and SubwooferConnecting the speakers AM Loop AntennaPlacing speakers Connecting Audio/Video ComponentsConnecting the subwoofer Analog ConnectionsVideo component connections DVD playerVideo camera, etc Digital Connections Connecting the Power CordPlug the power cord into an AC outlet Digital input terminalsDaily Operational Procedure Selecting the Source to Play Turning On the PowerBasic Operations Sound Adjusting the VolumeWhen analog input is selected Always lights up Picture from a video component such as the VCR or DVDPress Subwoofer OUT ON/OFF to cancel the subwoofer output Selecting the Analog or Digital Input ModeListening with headphones Turning On and OffAttenuating the Input Signal Changing the Source NameChanging the Display Brightness Muting the Sound Using the Sleep TimerBasic adjustment auto memory Recording a sourceUsing Preset Tuning Setting the AM Tuner Interval SpacingTuning in to Stations Manually Receiving Radio BroadcastsWhile listening to an FM station, press FM Mode Press the number buttons to select a preset channel numberSelecting the FM Reception Mode To tune in a preset stationPress Quick Speaker Setup Basic SettingsQuick Speaker Setup Channel numberPress Setting Basic Setting ItemsBasic Procedure Ex. When setting Virtual Surround Back to Vrtl SB onSetting the Speakers Setting the Speaker DistanceSetting the Bass Sounds Selecting the Main or Sub Channel Select the playback sounds channelSelect Vrtl SB on to activate Virtual Surround Back Setting for Effective Surround OperationsSetting the Digital Input Terminals Set the components connected to the digital terminalsPress Adjust Adjusting SoundBasic Adjustment Items Ex. When adjusting the subwoofer level toAdjusting the Equalization Patterns Adjusting the Speaker Output LevelsDolby Digital*1 Using the Surround ModesReproducing Theater Ambience Introducing the Surround Modes Dolby Digital 5.1CHDTS Digital Surround What is Linear PCM?What is Dual Mono? DTS 96/24Press Surround to activate the Surround mode Activating the Surround ModesSelect and play any source Introducing the DSP Modes Using the DSP ModesReproducing the Sound Field Digital Acoustic Processor DAP modesActivating the DSP Modes To cancel the DSP modeMulti-channel digital signals All Channel StereoSound control section Amplifier Operating JVC’s Audio/Video ComponentsOperating Audio Components TunerSelect a disc number Operating Video ComponentsCD changer DVD playerTroubleshooting Problem Possible Cause SolutionAmplifier SpecificationsOutput Power AudioFM tuner IHF AM tunerGeneral Receiver
Top Page Image Contents