Setting the Speakers for the DSP Modes
To obtain the best possible surround sound of the DSP modes, you have to register the information about the speakers arrangement after all connections are completed.
Before you start, remember....
•There is a time limit in doing the following steps. If the setting is canceled before you finish, start from step 1 again.
Center Delay Time Setting
Register the delay time of the sound from the center speaker, comparing that of the sound from the front speakers.
If the distance from your listening point to the center speaker is equal to that to the front speakers, select 0 msec. As the distance to the center speaker becomes shorter, increase the delay time.
•1 msec increase (or decrease) in delay time corresponds to 30 cm (11 13/16 inches) decrease (or increase) in distance.
•When shipped from the factory, delay time is set to 0 msec.
English
Front, Center, and Rear Speaker Setting
Register the sizes of all the connected speakers.
•When you change your speakers, you need to register the information about the speakers again.
On the front panel ONLY:
1. Press SETTING repeatedly until “CENTER DELAY” appears on the display.
SETTING
On the front panel ONLY:
1. Press SETTING repeatedly until | SETTING |
“FRONT SPK” (Front Speaker), |
|
“CENTER SPK” (Center |
|
Speaker) or “REAR SPK” (Rear |
|
Speaker) appears on the display. |
|
The display changes to show the current setting. |
|
| MULTI JOG |
2.Turn MULTI JOG to select the appropriate item about the speaker selected in the above step.
• As you turn it, the display changes to show the following:
LARGE
SMALL
NONE 
LARGE: Select this when the speaker size is relatively large.
SMALL: Select this when the speaker size is relatively small.
NONE: Select this when you have not connected a speaker. (Not selectable for the front speakers)
3.Repeat steps 1 and 2 to select the appropriate items for the other speakers.
Notes:
•Keep the following comment in mind as reference when adjusting.
–If the size of the cone speaker unit built in your speaker is greater than 12 cm (4 3/4 inches), select “LARGE,” and if it is smaller than 12 cm (4 3/4 inches), select “SMALL.”
•If you have selected “NO” for the subwoofer setting, you can only select “LARGE” for the front speaker setting.
•If you have selected “SMALL” for the front speaker setting, you cannot select “LARGE” for the center and rear speaker settings.
The display changes to show the current setting.
MULTI JOG
2.Turn MULTI JOG to select the delay time of the center speaker output.
•Turn it clockwise to increase the delay time from 0 msec (“C. DELAY: 0ms”) to 5 msec (“C. DELAY: 5ms”).
•Turn it counterclockwise to decrease the delay time from 5 msec (“C. DELAY: 5ms”) to 0 msec (“C. DELAY: 0ms”).
Note:
Center delay time setting is not valid for the DVD MULTI playback
mode.
Rear Delay Time Setting
Register the delay time of the sound from the rear speakers, comparing that of the sound from the front speakers.
If the distance from your listening point to the rear speakers is equal to that to the front speakers, select 0 msec. As the distance to the rear speakers becomes shorter, increase the delay time.
•1 msec increase (or decrease) in delay time corresponds to 30 cm (11 13/16 inches) decrease (or increase) in distance.
•Rear delay time for Dolby Digital, DTS Digital Surround, and MPEG Multichannel is to be set to 5 msec.
•When shipped from the factory, delay time is set to 5 msec.
On the front panel ONLY: | SETTING |
|
1.Press SETTING repeatedly until “REAR DELAY” appears on the
display.
The display changes to show the current setting.
MULTI JOG
2.Turn MULTI JOG to select the delay time of the rear speaker output.
•Turn it clockwise to increase the delay time from 0 msec (“R. DELAY: 0ms”) to 15 msec (“R. DELAY: 15ms”).
•Turn it counterclockwise to decrease the delay time from 15 msec (“R. DELAY: 15ms”) to 0 msec (“R. DELAY: 0ms”).
Note:
Rear delay time setting is not valid for the DVD MULTI playback mode.
14