JVC LVT0178-001A, RX-889PGD manual Troubleshooting, Problem Possible Cause Solution

Page 53

Troubleshooting

Use this chart to help you solve daily operational problems. If there is any problem you cannot solve, contact your JVC service center.

	PROBLEM	POSSIBLE CAUSE	SOLUTION

	The display does not light up.	The power cord is not plugged in.	Plug the power cord into an AC outlet.

	No sound from speakers.	Speaker signal cables are not connected.	Check speaker wiring and reconnect if
			necessary.

		The SPEAKERS 1 and 2 buttons are not	Press SPEAKERS 1 and 2 correctly.
		set correctly.

		An incorrect source is selected.	Select the correct source.

		Muting is activated.	Press MUTING to cancel the mute.

	Sound from one speaker only.	Speaker signal cables are not connected	Check speaker wiring and reconnect if
		properly.	necessary.

		The balance is set to one extreme.	Adjust the balance properly (see page 12).

	Continuous hiss or buzzing during FM	Incoming signal is too weak.	Connect an outdoor FM antenna or contact
	reception.		your dealer.

		The station is too far away.	Select a new station.

		An incorrect antenna is used.	Check with your dealer to be sure you have
			the correct antenna.

		Antennas are not connected properly.	Check connections.

	Occasional cracking noise during FM	Ignition noise from automobiles.	Move the antenna farther from automobile
	reception.		traffic.

	No colors on the on-screen display.	The color system of the connected TV is	Connect a PAL- or multi-color system TV.
		not PAL.

	Howling during record playing.	Your turntable is too close to speakers.	Move speakers away from the turntable.

	“OVERLOAD” starts flashing on the	Speakers are overloaded because of high	Rotate the MASTER VOLUME control
	display.	volume.	counterclockwise three or four times, then
			press STANDBY/ON					on the front panel.


			If “OVERLOAD” does not disappear, unplug
			the AC power cord, then plug it back again.

		Speakers are overloaded because of short	Press STANDBY/ON					on the front panel,


		circuit of speaker terminals.	then check the speaker wiring.
			If “OVERLOAD” does not disappear, unplug
			the AC power cord, then plug it back again.
			If speaker wiring is not short-circuited, contact
			your dealer.

	Remote control does not work.	The remote control mode selector is not	Set the selector correctly either to “AUDIO/
		set correctly.	TV/VCR” or to “CATV/DBS.”

		There is an obstruction in front of the	Remove the obstruction.
		remote sensor on the receiver.

		Batteries are weak.	Replace batteries.

English

50

Image 53

Contents RX-889PGD Precaución English Español Table of Contents Front Panel Remote ControlParts Identification Checking the Supplied Accessories Before Installation Connecting the FM and AM AntennasSetting the Voltage Selector Switch Getting StartedBasic connecting procedure Connecting the SpeakersConnecting the front speakers AM Antenna ConnectionsConnecting the rear and center speakers Connecting Audio/Video ComponentsConnecting the subwoofer speaker About the speaker impedanceTo audio input Cassette deck To audio output CD playerVHS or VHS VCR To audio input MD recorder To audio outputTo composite To S-video output‚ To composite video output DVD playerPutting Batteries in the Remote Control Connecting the Power CordPlug the power cord into an AC outlet Digital connectionsFrom the remote control Turning the Power On and Off StandbyBasic Operations Selecting the Source to PlaySelecting the Front Speakers Adjusting the VolumeEtc Selecting different sources for picture and soundListening at Low Volume Loudness Attenuating the Input SignalAdjusting the Subwoofer Output Level Muting the SoundAdjusting the Front Speaker Output Balance Basic SettingsSetting the Subwoofer Information Recording a SourceShowing the Text Information on Display Digital Input Digital in Terminal SettingSelecting the Analog or Digital Input Mode Center Delay Time Setting Setting the Speakers for the DSP ModesFront, Center, and Rear Speaker Setting Rear Delay Time SettingLow Frequency Effect Attenuator Setting Crossover Frequency SettingDynamic Range Compression Setting Frequency appears on the displayUsing the Sleep Timer Setting the AM Tuner Interval SpacingAdjust the sound using the functions listed above Press ONE Touch OPERATION. OnetouchoperationReceiving Radio Broadcasts Using Preset TuningTuning in Stations Manually Selecting the FM Reception Mode Assigning Names to Preset StationsCreating Your Own SEA Mode Using the SEA ModesSelecting Your Favorite SEA Mode DAP modes Using the DSP Modes3D-PHONIC modes Surround modes DVD Multi Playback ModeFront Available DSP Modes According to the Speaker ArrangementAdjusting the DAP Modes Adjusting the 3D-PHONIC ModesAdjusting the Surround Modes Adjust the center tone An appropriate Surround modePress DOLBY/DTS/MPEG Surround ON/OFF to activateRepeatedly until Theater or JVC Theater Surround adjustmentsDIG Theater appears on Display Press Test to check the speakerLamp on the button lights up Activating the DSP ModesSelect and play a sound source Press Surround ON/OFF soTo cancel the DSP mode Mode you want appears on DisplayPress Surround Mode repeatedly until For the other DSP modesActivating the DVD Multi Playback Mode Using the DVD Multi Playback ModeDVD Multi appears on Display Tone appears on the displayMulti appears on the display 10 keys are activated for adjusting the soundPress DVD Multi so that DVD Using the On-Screen Menus To Loudness Input Attenuator modePress @/ #to turn Loudness on orActivating the DVD Multi Playback Mode To SEA ModeSelecting Your Favorite SEA Mode Creating Your Own SEA ModePress SET to store the setting into the SEA Usermode Press %/ Þ/ @/ #to adjust the SEA mode as you wantPress %/ Þto move to SETTING, then Press @/ # Setting the Basic Setting Items Also seePreset station number Press %/ Þto move to Preset Name Then press SETPress %/ Þto move to Tuner CONTROL, then press @/ # Press %/ Þ / @/ #to Move in front of a character you wantRemote Control through the Remote Sensor on the Receiver Compu Link Remote Control SystemSame time Automatic Source SelectionCD player MD recorder Text Compu Link Remote Control SystemDisplaying the Disc Information on the TV screen Disc Search Only for CD PlayerShowing the Disc Information on the TV Screen Press Text Display while CD or MD is selected as the sourceTo exit from the Disc information screen Disc Information screen appears on the TVPress %/ Þto move to SEARCH, then Press SET Press Text Display while CD is selected as the sourcePress %/ Þto move To Performer Then press SET Press SET againPress %/ Þto move To GENRE, then Press SET Press %/ Þto move to Search Then press SETPress %/ Þto move To Title INPUT, then press SET Entering the Disc InformationPress %/ Þto move to the genre you want, then press SET Press Text Display while MD is selected as the sourceTo insert a space, press %/ Þ To correct an incorrect characterSound control section Amplifier Operating JVC’s Audio/Video ComponentsCD player CD player-changer TunerCassette deck TurntableMD recorder DVD playerOperating Other Manufacturers’ Video Equipment If there are more than one code listed for your brand of TVRelease TV/CATV/DBS Try to operate your TV by pressing TV/CATV DBSTry to operate your VCR by pressing VCR If there are more than one code listed for your brandRelease VCR Manufacturers’ codes for TV Manufacturers’ codes for DBS tuner Manufacturers’ codes for Catv converters SEI Problem Possible Cause Solution TroubleshootingVideo SpecificationsAmplifier FM tuner IHF Tuning Range Usable Sensitivity Signal-to-Noise RatioAM tuner GeneralPrecaução para a ligação à tensão da rede CA Precaución para la línea de la red CA