JVC LVT0142-006A, RX-669PGD manual Basic Settings, Changing the Source Name, Press TAPE/MD

Page 14

English

Basic Settings

Some of the following settings are required after connecting and positioning your speakers in your listening room, while others will make operations easier.

Changing the Source Name

When you have connected an MD recorder to the TAPE/MD jacks on the rear panel: Change the source name shown on the display when you select the MD recorder as the source.

On the front panel ONLY:

When changing the source name from “TAPE” to “MD”:

3. Press cursor control @/ #to select your center speaker size.

LARGE SMALLNONE

LARGE: Select this mode when the size of the center speaker is the same as that of the front speakers.

1.Press TAPE/MD.

• Make sure “TAPE” appears on the display.

2.Press and hold SOURCE NAME (the same button as TAPE/MD) until “ASSGN. MD” appears on the display.

TAPE/MD

SOURCE NAME

TAPE/MD

SOURCE NAME

SMALL: Select this mode when the size of the center speaker

is smaller than that of the front speakers.

NONE: Select this mode when you do not use a center speaker.

Rear Speaker Setting

Register whether you have connected the rear speakers or not.

To change the source name from “MD” to “TAPE,” repeat

the same procedure above (in step 1, make sure “MD” appears on the display).

Note:

Without changing the source name, you can still use the connected components. However, there may be some inconvenience.

–“TAPE” will appear on the display when you select the MD recorder.

–You cannot use the COMPU LINK remote control system (see page 25) to operate the MD recorder.

Setting Center and Rear Speakers for

the DSP Modes

To obtain the best possible surround sound of the DSP (Digital Signal Processor) modes (see page 17), you have to register the information about the speakers arrangement after all connections are completed.

Center Speaker Setting

Register the center speaker size.

Before you start, remember....

•There is a time limit in doing the following steps. If the setting is canceled before you finish, start from step 1 again.

Before you start, remember....

•There is a time limit in doing the following steps. If the setting is canceled before you finish, start from step 1 again.

On the front panel ONLY:

1. Press SETTING so that the cursor

SETTING

control % / Þbuttons work for

 

setting the rear speaker

 

information.

 

2. Press cursor control %/ Þ repeatedly until “REAR SPK” (Rear Speaker) appears on the display.

3. Press cursor control @/ #to register whether you have connected the rear speakers.

YES: Select this mode when you use rear speakers.

NO: Select this mode when you do not use rear speakers.

Note:

When you change your speakers, you need to register the information

about the speakers again.

On the front panel ONLY:

SETTING

1. Press SETTING so that the cursor control %/ Þbuttons work for setting the center speaker size.

2. Press cursor control % / Þ repeatedly until “CENTER SPK” (Center Speaker) appears on the display.

Delay Time Setting

Register the delay time of the sound from the rear speakers, comparing the sound from the front speakers. Delay time is only valid for “PRO LOGIC.” (See page 15.)

Before you start, remember....

•There is a time limit in doing the following steps. If the setting is canceled before you finish, start from step 1 again.

•You can adjust the delay time only when you have connected the rear speakers and have set “REAR SPK” to “YES” (See above).

11

Page 13 Page 15
Image 14
Page 13 Page 15
Contents RX-669PGD Precaución English Table of Contents To use the Cursor control buttons q on the front panel Front Panel Remote ControlParts Identification Setting the Voltage Selector Switch Before Installation Connecting the FM and AM AntennasChecking the Supplied Accessories Getting StartedConnecting the front speakers Connecting the SpeakersBasic connecting procedure Connecting the rear and center speakersAudio component connections Connecting Audio/Video ComponentsConnecting the subwoofer speaker Video component connections TV as the monitorPlug the power cord into an AC outlet Connecting the Power CordPutting Batteries in the Remote Control Replace the coverBasic Operations Turning the Power On and Off StandbyFrom the remote control On the front panelRecording a Source Selecting the Front SpeakersMuting the Sound Adjusting the Tone Attenuating the Input SignalAdjusting the Front Speaker Output Balance Reinforcing the BassPress Setting so that the cursor Basic SettingsSetting Center and Rear Speakers for DSP Modes Changing the Source NamePress ONE Touch Operation Using the Sleep TimerAdjust the sound using the functions listed above Receiving Radio Broadcasts Setting the AM Tuner Interval Spacing Using Preset TuningTuning in Stations Manually When an FM stereo broadcast is hard to receive or noisy Press 10 keys to select a preset channel numberTo tune in a preset station Press FM/AMSurround Modes Using the DSP Modes3D-PHONIC modes Dolby SurroundAvailable DSP Modes According to the Speaker Arrangement Speaker arrangements Available DSP modesAdjusting the 3D-PHONIC Modes Adjusting DAP Digital Acoustic Processor ModesPress Test to check the speaker Press Rearl / + to adjust the rear speaker output levelUntil the mode PRO Logic Or Theater appears on Display Output balanceActivating the DSP Modes Press Surround repeatedly Until the DSP mode you wantTo cancel the DSP mode Select and play a sound sourceUsing the DVD Multi Playback Mode Activating the DVD Multi Playback ModeUsing the On-Screen Menus Press %/ Þto move to Sound CONTROL, then press @/ # Press % / Þto move To Bass Boost Press @/ #to turnPress any one of %/ Þ / @/ # @/ #Press % / Þto move to Surround LEVEL, then press @/ # Press %/ Þ/ @/ #to adjust the tone as you wantPress %/ Þto move to SETTING, then press @/ # Press %/ Þto move to Tone CONTROL, then press @/ #Preset Memory menu Appears Press %/ Þto move To Preset MEMORY, then press @/ #Storing the Preset Stations Also see Press %/ Þto move To Tuner CONTROL, then Press @/ #Same time Compu Link Remote Control SystemRemote Control through the Remote Sensor on the Receiver Automatic Source SelectionDisc Search Only for CD Player Text Compu Link Remote Control SystemDisplaying the Disc Information on the TV screen Disc Title InputTo exit from the Disc information screen Press Text Display while CD or MD is selected as the sourceShowing the Disc Information on the TV Screen Press %/ Þto move to Performer Then press on Press Text Display while CD is selected as the sourcePress %/ Þto move to SEARCH, then press on Screen SET Press on Screen SET againThen press on Screen SET Press %/ Þto move To Search Then press onPress %/ Þto move To GENRE, then Press on Screen Entering the Disc InformationPress Text Display while MD is selected as the source Up to 32 charactersEnter the disc title, referring to steps 3 For the MD recorderSound control section Amplifier Operating JVC’s Audio/Video ComponentsTuner CD playerDVD player Cassette deckMD recorder Troubleshooting Problem Possible Cause SolutionFM tuner IHF SpecificationsAmplifier AM tunerPrecaução para a ligação à tensão da rede CA Precaución para la línea de la red CA

RX-669P, RX-669PGD, LVT0142-006A specifications

JVC, a renowned name in the world of audio and visual technology, continues to impress with its range of high-quality products. Among these, the JVC LVT0142-006A, RX-669PGD, and RX-669P stand out for their remarkable features and performance.

The JVC LVT0142-006A is primarily recognized as a versatile speaker system designed to complement various home audio setups. This model boasts a sleek design that seamlessly fits into any environment, with a focus on delivering powerful sound. It integrates advanced audio technologies to ensure clarity and precision in output, making it suitable for music lovers and film enthusiasts alike. The speaker also supports a range of input options, allowing users to connect multiple devices effortlessly.

Moving on to the RX-669PGD, this receiver is packed with features tailored for optimal sound reproduction and comprehensive connectivity. It supports a variety of audio formats, ensuring that listeners can enjoy their favorite music in multiple ways. The RX-669PGD is equipped with an integrated amplifier that delivers robust power, providing an immersive listening experience. Its user-friendly interface allows for easy navigation, while the built-in Bluetooth capability enables wireless streaming from smartphones and tablets.

The RX-669P model takes the legacy of the RX-669PGD further by incorporating extensive compatibility options. It features multiple HDMI inputs and outputs, making it an excellent choice for home theater setups. This model supports 4K video passthrough, ensuring that users can enjoy high-resolution content without any loss in quality. With its surround sound capabilities, the RX-669P transforms any living space into a dynamic audio environment, significantly enhancing the viewing experience of movies and shows.

All three products embody JVC’s commitment to quality and innovation. They utilize cutting-edge materials in their construction, ensuring durability and longevity. Furthermore, the design philosophy behind these models emphasizes not only performance but also aesthetics, making them attractive additions to any home.

In summary, the JVC LVT0142-006A, RX-669PGD, and RX-669P are exemplary products that showcase JVC's dedication to delivering high-fidelity audio solutions. With their advanced features, versatile connectivity options, and sleek designs, they cater to the demands of modern consumers while enhancing the overall audio experience.
Top Page Image Contents