JVC RX-DP9VBK manual Operating Video Components, VCR VCR connected to the VCR 1 jacks, DVD player

TV

CATV/

DBS

Operating Video Components

IMPORTANT:

To operate JVC’s video components using this remote control:

•You need to connect JVC video components through the AV COMPU LINK jacks (see page 53) in addition to the connections using cables with RCA pin plugs (see pages 11 to 13).

•Some JVC VCRs can accept two types of the control signals— remote codes “A” and “B.” Before using this remote control, make sure that the remote control code of the VCR connected to the VCR 1 jacks is set to code “A.”

–When another JVC VCR is connected to the VCR 2 and VIDEO jacks, set its remote control code to code “B.” (This remote control cannot emit the control signals of code “B.”)

•To operate the video component(s) using the remote control:

–Aim the remote control directly at the remote sensor on each component, not on the receiver.

When using the remote control:

– Set the TV operation mode selector to “TV” or “CATV/DBS” correctly.

To operate TV, set it to “TV.”

–Check the indication shown on the remote’s display when you press a button—this indicates the remote control operation mode for a while (10 or 5 seconds).

–The CONTROL button can change the remote control operation mode without changing the source.

Each time you press the button, the remote control operation mode changes in the sequence—VCR1 =TAPE =CDR =CDDSC =(back to the beginning).

STANDBY ON

TV/CATV/DBS VCR 1

STANDBY/ON STANDBY/ON

Ex. When you press VCR1.

VCR (VCR connected to the VCR 1 jacks)

You can always perform the following operations:

VCR 1 (STANDBY/ON): Turns on or off the VCR.

After pressing VCR 1 or selecting “VCR1” by pressing CONTROL repeatedly, you can perform the following operations on a VCR:

1 – 9, 0	: Selects the TV channels on a VCR.
PLAY	: Starts playing.
REW	: Rewinds a tape.
FF	: Fast-winds a tape.
STOP	: Stops operations.
PAUSE	: Pauses playing. To release it, press PLAY.
ƒ REC	: Press this button together with the PLAY button

to start recording.

Press this button together with the PAUSE button to enter recording pause.

CHANNEL +/– : Changes the TV channels on a VCR.

Note:

You can use either the VCR 1 button or the CONTROL button to activate the buttons listed above. If you press VCR 1, the playing source also changes. On the other hand, if you press CONTROL repeatedly to select “VCR1” on the remote’s display, the playing source does not change.

DVD player

After pressing DVD (or DVD MULTI), you can perform the following operations on a DVD player:

1 – 10, 0, +10 : Selects the DVD titles or the chapters.

PLAY : Starts playing.

4: Returns to the beginning of the current (or

previous) chapter.

¢: Skips to the beginning of the next chapter.

STOP	: Stops playing.
PAUSE	: Stops playing temporarily. To release it, press
	PLAY.

After pressing DVD MENU , these buttons can be used for the DVD menu operations.

SET

DVD

EXIT

MENU

Note:

Refer also to the manual supplied for your DVD player (and the instruction supplied for the discs).

TV

You can always perform the following operations (with the TV operation mode selector set to “TV”):

TV/CATV/DBS (STANDBY/ON) : Turns on or off the TV.

TV VOL +/– : Adjusts the volume.

TV/VIDEO : Sets the input mode (either TV or VIDEO).

After pressing TV/DBS (with the TV operation mode selector set to “TV”), you can perform the following operations on a TV:

CHANNEL +/– : Changes the channels.

1 – 9, 0, 100+ : Selects the channels.

RETURN : Alternates between the previously selected channel and the current channel.

57