JVC RX-DP9VBK manual Press DVD, Press and hold Audio on, Press CD, Release Audio on

Page 63

To change the transmittable signals for operating a DVD player

To change the transmittable signals for operating a CD player

1.Press and hold VCR 1

(STANDBY/ON).

2.Press DVD.

Remote’s display

3. Enter manufacturer’s code using buttons 1–9, and 0.

See page 61 to find the code.

VCR 1

STANDBY/ON

DVD

EFFECT

1 2 3

 

 

ROOM SIZE

4

5

6

LIVENESS

1. Press and hold AUDIO (ON).

STANDBY ON

2. Press CD.

CD

Remote’s display

3. Enter manufacturer’s code using

EFFECT

7/P

8

9

 

 

WALL

10

0

+10

RETURN

FM MODE

100+

4. Release VCR 1 (STANDBY/ON).

After pressing DVD (or DVD MULTI), you can perform the following operations on a DVD player:

1 – 9, 0, +10: Selects the titles or the chapters.

PLAY : Starts playing.

4: Returns to the beginning of the current (or previous) chapter.

¢: Skips to the beginning of the next track.

STOP : Stops playing.

PAUSE : Stops playing temporarily. To release it, press PLAY.

After pressing DVD

MENU, these buttons can be used for the DVD menu

operations.SET

DVD

EXIT

MENU

Note:

Refer also to the manual supplied for your DVD player (and the instruction supplied for the discs).

5.Try to operate your DVD player by pressing one of the above buttons.

DO NOT forget to turn on the DVD player before pressing one of the above buttons.

If there are more than one code listed for your brand of DVD

player, try each one until the correct one is entered.

buttons 1–9, and 0.

1

2

3

 

 

ROOM SIZE

See page 61 to find the code.

4

5

6

 

 

LIVENESS

 

 

 

 

7/P

8

9

 

 

 

WALL

 

10

0

+10

 

RETURN

FM MODE

100+

4. Release AUDIO (ON).

After pressing CD, you can perform the following operations on a CD player:

1 – 9, 0, +10: Selects the tracks.

PLAY

: Starts playing.

REW

: Fast-reverses the tracks.

FF: Fast-forwards the tracks.

STOP : Stops playing.

PAUSE : Stops playing temporarily. To release it, press PLAY.

Note:

Refer to the manual supplied for your CD player.

5.Try to operate your CD player by pressing one of the above buttons.

• DO NOT forget to turn on the CD player before pressing one

of the above buttons.

If there are more than one code listed for your brand of CD,

try each one until the correct one is entered.

60

Image 63
Contents RX-DP9VBK 21.1 kg / 47 lb Cautio -- STANDBY/ON switchPage Table of Contents Features PrecautionsIntroduction For more details, see Parts IdentificationFront Panel Display WindowTuned indicator Analog indicatorDigital Auto indicator Surround/DSP mode indicatorsSetup MENU, Adjust MENU, SET, EXIT, %UP DOWN, @LEFT, #RIGHT Remote ControlSignal transmission indicator Lights up when transmitting the remote control signalsGetting Started Before InstallationConnecting the FM and AM Antennas Checking the Supplied AccessoriesSpeaker layout Connecting the SpeakersAM Antenna Connections Turn the loop until you have the best receptionImportant for the Front 1 Speakers connection Basic connecting procedureConnecting the surround back speakers Connecting the subwoofer speakerTurntable Connecting Audio/Video ComponentsEnhance your audio system Analog ConnectionsCD player CD recorderCassette deck or MD recorder VCRs VHS or VHS VCRVideo camera DBS tuner TV and/or DBS tunerDVD player Digital Connections Digital input terminalsDigital output terminal Replace the cover Connecting the Power CordPutting Batteries in the Remote Control Plug the power cord into an AC outletBasic Operations Simple Operating ProcedureSelecting the Source to Play Turning the Power On and Off StandbyPress one of the source selecting buttons Speaker and signal indicators on the displayFront door while viewing Picture from a video componentAdjusting the Volume Activating the Front Speakers Before you start, remember Selecting the Analog or Digital Input ModeSelect this for the analog input mode Analog indicator lights upAttenuating the Input Signal Turning Line Direct On and OffMuting the Sound Making Sounds Natural Changing the Source NameChanging the Display Brightness To cancel the Sleep Timer Using the Sleep TimerBasic adjustment auto memory When the shut-off time comesPress UP or Down inside Tuning into Stations ManuallyReceiving Radio Broadcasts Press FM or AMSelecting the FM Reception Mode Using Preset TuningSetup Menu Configuration Basic SettingsOperation through On-Screen Display Menus Menu operation buttonsButton To do Set other items on the same submenu if necessary Menu Operating ProcedurePress Setup Menu Press SETFor measuring unit Select this when a subwoofer is connectedSelect this when no subwoofer is used For subwooferSetting the Bass Sounds-SUBWOOFER Setting the Dynamic Range -DYNAMIC Range Setting the Surround Sound Output -SURROUND SpeakerPreparing for THX Surround Modes-THX Preparing for the Component Video Input -COMPONENT Setting the Digital Input Terminals -DIGITALSetting the component connected to the digital Setting the component video input terminalsTo cancel the One Touch Operation Turning On and Off the Video Output -VIDEO PowerSelect this not to store the volume level setting To recall the volume levelAdjustment Menu Configuration Sound AdjustmentsEx. When you press Adjust Menu Adjust MenuOn the front panel Press Adjust Menu Ex.When adjusting a DSP parameterWhen adjusting the parametric equalizer Adjusting the Parametric Equalizer -PARAMETRIC EQ Adjusting the Speaker Channel Output Levels-LEVELAdjusting the Center Channel -CENTER Channel Adjusting the DSP Parameters -DSP ParameterTHX Surround EX Dolby Digital EX Using the Surround ModesReproducing Theater Ambience Introducing the Surround ModesDTS Surround 3D Headphone ModeDVD Multi Playback Mode Dolby Surround Dolby Pro LogicSelect and play one of the following sound sources To cancel the THX SurroundTo cancel the conventional Surround mode Activating the Surround ModesAdjusting the Surround Sounds Temporarily Using the DSP Modes Reproducing the Sound FieldIntroducing the DSP Modes If the center speaker is connected and activated Headphone ModeWithout connecting the surround speakers Activating the DSP ModesAdjusting the DSP Parameters Temporarily Press DVD Multi so that DVD Multi appears on the display Using the DVD Multi Playback ModeActivating the DVD Multi Playback Mode Ex. When you press DVD MultiCompu Link Remote Control System Same timePress the play 3 button on the CD player Disc Search Only for CD Player Text Compu Link Remote Control SystemCD player MD recorder Displaying the Disc Information on the TV screenText display operation buttons Ex. When you press Text DisplayPress Text Display while CD or MD is selected as the source Showing the Disc Information on the TV ScreenPress SET again Press Text Display while CD is selected as the sourcePress %/ Þto move to SEARCH, then press Press %/ Þto move to Performer Then press SETOn the Search Press %/ Þto move to SEARCH, then press SETPress %/ Þto move To GENRE, then Press SET Press %/ Þto move To the genre you Want to search forTo correct an incorrect character Press Text Display while MD is selected as the sourcePress %/ Þto move to the genre you want, then press SET To insert a space, pressCase AV Compu Link Remote Control SystemConnections 1 AV Compu Link Connection Connections 2 Video Cable ConnectionOne-Touch DVD Play Automatic Selection of TV’s Input ModeAutomatic Power On/Off One-Touch Video PlaySound control section Amplifier Operating JVC’s Audio/Video ComponentsOperating Audio Components TunerCD recorder CD playerCD player-changer Turntable Operating Video Components VCR VCR connected to the VCR 1 jacks DVD player Operating Other Manufacturers’ Equipment Changing the Preset Signal CodesButtons 1-9, Enter manufacturer’s code usingPress and hold VCR Press VCRPress CD If there are more than one code listed for your brand of CDPress DVD Press and hold Audio onManufactures codes for VCR Manufacturer Codes Manufactures codes for TV Manufacturer CodesManufactures codes for DBS tuner Manufacturer Codes Manufactures codes for Catv converter Manufacturer CodesProblem Possible Cause Solution TroubleshootingVideo SpecificationsAmplifier AudioAM tuner Tuning Range KHz to 1 710 kHz Usable SensitivitySignal-to-Noise Ratio 50 dB 100 mV/m FM tuner IHFAuthorized Service Centers Limited Warranty 0701NHMMDWJEIN
Related manuals
Manual 70 pages 34.14 Kb