Life Fitness UT8, RT8 user manual UMN Bracket

Page 8

5.Connect the CONNECTOR (J) leading from the HANDLE- BAR ASSEMBLY (E) with the CONNECTOR (J) leading from the SEAT ASSEMBLY (F). Be sure the connectors fully lock.

CAUTION: To ensure that your handsensor heart rate works properly, secure the HEART RATE CABLE (K) into the CABLE TIE CLIPS (G). Note the routing of the HEART RATE CABLE so as to not pinch the HEART RATE CABLE between the SEAT and the SEAT ASSEM- BLY during assembly.

6.Locate the SEAT BOTTOM (L). Align the SEAT BOTTOM mounting holes with those in the LOWER SEAT SUPPORT TUBES (M). Secure the SEAT BOTTOM using four 2" PHILLIPS SCREWS (6) and LOCK WASHERS (7). Tighten the SCREWS securely.

7.Align the guide rollers located on the underside of the SEAT ASSEMBLY (F) with the SEAT EXTRUSION (N). Carefully guide the SEAT ASSEMBLY onto the SEAT EXTRUSION. Slide the SEAT ASSEMBLY fully forward. Connect the WIRE

(O) leading from the user left side of the SEAT ASSEMBLY to the jack located at the left front of the SEAT EXTRUSION.

8.In the hole located in the user right side of the SEAT EXTRU- SION (J), behind SEAT ASSEMBLY (F), install one 1-3/8" BUTTON HEAD SCREW with locktite (7), two 15/16" FLAT WASHERS (8), one RUBBER BUMPER SLEEVE (9) and one 1" RUBBER BUMPER (10) as shown.

9.Mount the SEAT ADJUSTMENT LEVER (P) to the user right side of the SEAT ASSEMBLY (F) using two 3/4" PHILLIPS SCREWS (11). Tighten the SCREWS securely.

10.Secure the SEAT BACK (Q) to the UPPER SEAT SUPPORT TUBES (R) using four 2" PHILLIPS SCREWS (6) and LOCK WASHERS (7). Tighten the SCREWS securely.

11.Locate the SEAT EXTRUSION ENDCAP (S). Secure the SEAT EXTRUSION ENDCAP to the SEAT EXTRUSION (N) using two 1/2" PHILLIPS SCREWS (12).

12.Locate the MONOCOLUMN (T). Cut the WIRE TIE securing the WIRE (U) to the bottom of the MONOCOLUMN. Slide the MONOCOLUMN COVER (V) onto the MONOCOLUMN as shown. Slide the MONOCOLUMN COVER up to the

HANDLEBAR TUBE (W).

13.Locate and insert the GROMMET (X) into the SIDE ACCESS HOLE (Y) of the MONOCOLUMN (T). Pull the WIRE (U) out through the SIDE ACCESS HOLE.

14.With the HANDLEBAR TUBE (W) facing the rear of the unit as shown, slide the MONOCOLUMN (T) into the MONO- COLUMN BRACKET (Z) of the BASE UNIT (C). Slide the MONOCOLUMN down until it is fully seated. Secure the MONOCOLUMN to the MONOCOLUMN BRACKET using two 3-15/16" HEX HEAD BOLTS (13) and three THICK FLAT WASHERS (14) (as shown) from the front side of the MONOCOLUMN and two 2-3/8" HEX HEAD BOLTS (15) and THICK FLAT WASHERS (14) from the user left side of the MONOCOLUMN BRACKET. Tighten the BOLTS secure- ly.

CAUTION: Be careful not to pinch the WIRE(s) (AA) leading from the MONOCOLUMN BRACKET (Z) when inserting the MONOCOLUMN (T) into the MONOCOL-

UMN BRACKET.

15.Connect the WIRE(s) (AA) leading from the MONOCOLUMN BRACKET (Z) to the corresponding WIRE (U) from the SIDE ACCESS HOLE (Y) of the MONOCOLUMN. Slide the MONOCOLUMN COVER (V) downward to the meet the MAIN SHROUDS (BB). Secure the MONOCOLUMN COVER to the MAIN SHROUDS using four 1/2" PHILLIPS SCREWS (12) and matching FLAT WASHERS (16). Tighten the SCREWS securely. Do not overtighten the SCREWS.

16.Locate the DISPLAY CONSOLE BRACKET (CC) and ACCESSORY TRAY (DD). While holding the WIRE(s)/CON- NECTOR (EE), cut the wire tie securing the CONNECTOR to the MONOCOLUMN (T). Position the DISPLAY CON- SOLE BRACKET and ACCESSORY TRAY near the top of the MONOCOLUMN. Feed the WIRE(s)/CONNECTOR lead- ing from the TOP ACCESS HOLE (FF) of the MONOCOL- UMN through the center hole of the DISPLAY CONSOLE BRACKET and the ACCESSORY TRAY. Secure the DIS- PLAY CONSOLE BRACKET and the ACCESSORY TRAY to the MONOCOLUMN using two 1" PHILLIPS SCREWS (17) and matching FLAT WASHERS (18). Tighten the SCREWS securely.

CAUTION: Be careful not the pinch the WIRE(s)/CON- NECTOR (EE) leading from the MONOCOLUMN (T)

when securing the DISPLAY CONSOLE BRACKET (Z) and ACCESSORY TRAY (DD) to the MONOCOLUMN.

NOTE: Be careful not to let the WIRE(s)/CONNECTOR (EE) fall into the MONOCOLUMN (T).

17.Remove the DISPLAY CONSOLE (GG) from its shipping carton. Position the above the ACCESSORY TRAY (DD). Connect the WIRE(s)/CONNECTOR (EE) leading from the DISPLAY CONSOLE BRACKET (Z) to the corresponding JACK(s) located on the back of the DISPLAY CONSOLE. Secure the DISPLAY CONSOLE to the DISPLAY CONSOLE BRACKET using four 1/2" PHILLIPS SCREWS (12). Tighten the SCREWS securely. Do not overtighten the SCREWS.

18.Locate the HANDLEBAR ASSEMBLY (HH). Position the HANDLEBAR ASSEMBLY near the top of the HANDLEBAR TUBE (W). Slide the HANDLEBAR ASSEMBLY fully into the HANDLEBAR TUBE. Secure the HANDLEBAR ASSEMBLY to the HANDLEBAR TUBE using four 5/8" BUTTON HEAD SCREWS (3) and matching FLAT WASHERS (4). Tighten the SCREWS securely.

19.Locate the RIGHT PEDAL (JJ) (marked with an "R") and PEDAL STRAP (KK) (marked with an "R"). With the side of the PEDAL STRAP marked with an “R” facing upward, slide the slotted end of the PEDAL STRAP through the left slot in the PEDAL. Fasten one of the slots onto the TAB located under the left slot of the PEDAL. Bend the PEDAL STRAP upward and slide the remaining end of the PEDAL STRAP through the right slot in the PEDAL and into the STRAP ADJUSTMENT CLIP. The PEDAL STRAP should securely engage the STRAP ADJUSTMENT CLIP.

20.Install the RIGHT PEDAL (JJ) to the USER RIGHT CRANK ARM (LL). Repeat for the LEFT PEDAL (MM) (marked with an "L") and PEDAL STRAP (NN) (marked with an "L").

NOTE: The LEFT PEDAL (MM) has reverse threads.

21.Position the unit in the desired location for use. The unit can be easily moved into place by lifting the rear of the unit and rolling it on the front rollers. Level the unit before use. Refer to the leveling instructions stated in the operations portion of this manual.

7

Page 7 Page 9
Image 8
Page 7 Page 9
Contents UT8 and RT8 Exercise Bikes Life Fitness Latin America and Caribbean Corporate HeadquartersInternational Offices Page Table of Contents Unpacking the Upright Exercise Bike Assembling Upright Exercise Bike ScrewsUnpacking the Recumbent Exercise Bike Assembling the Recumbent Exercise BikeUMN Bracket UT8 Important Safety Instructions Getting StartedSetup HOW to Stabilize the Exercise BikeHOW to Adjust the Pedal Straps Display Console Display Console OverviewDisplay Console Descriptions CLEAR/PAUSEAccessory Tray and Reading Rack Upright model picturedWHY Heart Rate Zone Training EXERCISE? Heart Rate Zone Training ExerciseHeart Rate Monitoring Upright model Recumbent modelTelemetry Heart Rate Chest Strap Workout Overviews Using the WorkoutsWorkouts Difficulty Resistance Exercise Bike Workout Setup Steps Workout DescriptionsHill Gradual Hill Workout Profile Cardio Hill Workout Profile 137 THR 130 THRCardio Interval Workout Profile Cardio Endurance Workout ProfileMY Workoutstm Personal Programs Changing a workout nameOptional Settings Optional SettingsPreventative Maintenance Schedule Service and Technical DataPreventative Maintenance Tips Troubleshooting the Telemetry Heart Rate Chest Strap Troubleshooting the Handpulse SensorsHOW to Obtain Product Service Specifications Upright Exercise Bike SpecificationsRecumbent Exercise Bike Specifications

RT8, UT8 specifications

The Life Fitness UT8 and RT8 models represent a significant advancement in the realm of commercial-grade fitness equipment. Designed for both gym operators and fitness enthusiasts, these machines cater to a wide range of user needs, providing an effective and engaging workout experience.

The UT8 (Upright Trainer) and RT8 (Recumbent Trainer) are engineered with state-of-the-art technology aimed at enhancing user engagement and workout efficiency. One of the standout features is the advanced touchscreen console, which utilizes a color LCD display. This interface is intuitive, allowing users to easily select workouts, track their progress, and access fitness apps. It also supports Bluetooth connectivity, enabling users to sync their devices and track performance metrics seamlessly.

Both machines come with a variety of pre-set workouts designed by fitness professionals, catering to different fitness levels and goals. The workout programs range from low-intensity warm-ups to high-intensity interval training, ensuring a comprehensive regimen for users. The ergonomic design of the seats and handlebars on both the UT8 and RT8 enhances user comfort while promoting proper posture during workouts.

A notable characteristic of the UT8 is its adjustable resistance levels, which empower users to personalize their training intensity. The RT8, on the other hand, is equipped with a unique reclined seat structure that offers superior support for the lower back, making it suitable for users with mobility concerns or those seeking a more gentle cardio workout.

Incorporating Life Fitness' innovative Flex Deck technology, both models are designed to reduce joint impact while maximizing stability and comfort during workouts. This technology is particularly beneficial for users looking to minimize the risk of injury while enhancing their cardiovascular fitness.

Both the UT8 and RT8 are built with durability in mind, featuring high-quality materials that ensure long-lasting performance even in busy gym environments. Their compact designs allow for efficient space utilization, making them perfect for facilities with limited floor space.

In summary, the Life Fitness UT8 and RT8 are sophisticated, user-friendly machines that combine advanced technology with superior comfort and safety features, making them ideal choices for commercial and home gym settings alike. With their diverse workout options and robust construction, these trainers are poised to meet the demands of any fitness enthusiast, regardless of experience level.
Top Page Image Contents