Apollo Radius manual One Piece Crank Assembly

Page 55

Lubrication and Adjustment – One Piece Cranks

To adjust:

-Turn the locknut on the left side clockwise to loosen.

-Turn the adjusting cone anti-clockwise with a screwdriver until correctly secured.

-Turn the locknut in an anti-clockwise direction to re-fasten.

To disassemble:

1.Take the chain from the chainwheel.

2.Turn the spindle clockwise and remove the left pedal.

3.Turn the left side locknut clockwise and remove, as well as the keyed lock washer.

4.Use a screwdriver to turn the adjusting cone clockwise and remove.

5.Remove the left ball retainer, slide the crank assembly out of the frame to the right, and remove the right ball retainer.

Once the crank is dismantled, clean all bearing surfaces and the ball retainers, and check for wear. Replace any damaged parts and pack grease into the ball bearing retainers. Re-assemble the crank in the reverse order of the procedure listed above.

Fixed Cone

Bearing Cup

Locknut

Lockwasher

Adjusting Cone

Ball Retainer

Bearing Cup

Ball Retainer

Crank

One Piece Crank Assembly

Chainwheel

53

Updated 23/05/07

RAOM0507

Apollo Bicycle Company Pty. Ltd. ABN: 60 001 914 469

Image 55
Contents Page Page Congratulations Contact Addresses Back Cover Warranty Inside Front CoverComprehensive Maintenance Before You Ride Pages 8Schedule Lubrication Schedule Service ChecklistCorrect Frame Size Riding PositionIdentifacation Gear Control Cable Chainwheel Crash Pad Handlebar Stem Handlebar Grip Brake Control Cable Frame Size Part 3 Before YOU RideApprox Wheel Suggested Saddle Height Riding PositionUpdated 23/05/07 RAOM0507 Safety Checklist Updated 23/05/07 RAOM0507 Helmets Riding Safely For dynamo powered lights Try to avoid where possibleCharge batteries if battery powered lights Are to be used. Check wiring connectionsUpdated 23/05/07 RAOM0507 Hand Grip Shifters Below Bar Shifters Dual Control Shifters Gears HOW to OperateDerailleur Gears Derailleur gears are the most common type To the riderRecommended Chainwheel/Rear Sprocket Gear Combinations Left Rapid Fire Shifters Bicycle Care Part 4 Bicycle Care & ServicingHigh Security using a U Lock Frequency Component Lubricate How to Lubricate Frequency Task Reference Schedule 2 Service ChecklistComponent Torque Wheels and Tyres Part 5 Comprehensive MaintenanceBMX MTB Updated 23/05/07 RAOM0507 RAOM0507 Correct Quick Release Axle Setting Hub to expose the ball bearings To properly re-adjust the bearing conesHub Lubrication Take the wheel out of the frameHow To Repair a Flat Tyre Schraeder is a registered Trademark Steering System Fork Rear wheel hub Single Allen key or hexagonal boltBicycle Suspension ‘Ahead Set’ Type Assemblies Headset InspectionUpdated 23/05/07 RAOM0507 Rotor Headset Inspection Saddle and Seat PostFrame RAOM0507 Foot Controlled Brakes BrakesLubrication calliper brakes Adjustment Sidepull Callipers39mm or more 5mm Allen Key Updated 23/05/07 RAOM0507 Brake Shoe Replacement Correct Pedal Attachment DrivetrainBicycle and falling Lubrication and Adjustment Crank arms This system requires more detailed servicingOne Piece Crank Assembly Use a coin or a screwdriver to remove the dust cap Screw in the removal tool Turn the screwbolt clockwise Front Chainwheel Rear Sprocket Pull Up Straightedge 12mm Updated 23/05/07 RAOM0507 RAOM0507 Derailleur Systems Or whenever new cables are fitted Adjustment Rear Derailleur To adjust low gear Chainring and the largest rear sprocket Turn the adjusting screw marked ‘L’ untilLoosen off the control cable fixing bolt To increase visibility ReflectorsAccessories Gloves Child Safety CarrierReplace bottom bracket or Clean blocks and rimSlipping chain Brake blocks worn Replace brake blocks They squeal/squeakRe-true if possible, or replace Part 6 PURCHASE DETAILS