Huffy M0012 manual Assemble the Front Wheel to the Fork Assembly, Loosen the Front Brakes

Page 12

Assemble the Front Wheel to the Fork

Assembly

Loosen the Front Brakes:

1.Squeeze the two Brake arms together

(A).

2.Lift out the Brake Cable Guide (B) from the Guide Bracket (C).

Install the Front Wheel:

3.Set the Front Wheel (3) into the front fork (4) (ﬁg 03).

4.Install wheel retainers (5) making sure the tabs are in the Fork Retainer Holes

(C).

5.Attach the front wheel with the Axle Nuts (6).

6.Tighten Axle Nuts to 21 ft-lbs.

WARNING: Do not use Nuts (6) without serrations to attach the front wheel.

6

B

A A C

fig 02

4

C

5 3

fig 03

NOTE: Ensure wheel spins freely without contacting fork or fender.

WARNING: Put the wheel in the center of the fork and tighten both nuts to the recommended torque of 21 ft.-lbs.

WARNING: Failure to obey these steps can allow the front wheel to loosen while riding. This can cause injury to the rider or to others.

12

Image 12

Contents For Mountain Bikes Your Bike Owner’s Bicycle Identiﬁcation Record Fitting the Rider to the Bicycle Your BikeModel / Serial Number Purchase Date Model Name Rules of the Road Meanings of WarningsIf you must ride at night or at time of poor visibility Use extra caution in wet weatherYour Bike Owner’s Responsibility Parts Assembly View Parts View Parts Assembly List Parts ListDescription Assembly Introduction Assembly Small Adjustable WrenchTools Needed Flat-blade ScrewdriverHandlebar and Stem Installation Quill Style StemThreadless Style Stem Assemble the Front Wheel to the Fork Assembly Install the Front WheelLoosen the Front Brakes Re-attache Front Brake Cable Re-attach Front Brake CableAssembly Setting Up the Handlebars Testing Stem and Handlebar Tightness To test the tightness of the stemTo test the tightness of the handlebar clamp Assembly Seat Installation Attach Seat to Seat Post pre-assembled on some modelsTighten the quick release lever Testing Seat Clamp and Post Clamp Tightness To test the tightness of the seat clamp and the post clampIf the seat moves in the Seat Clamp a ﬁg If the Seat Post 9 moves in the Seat Tube BAssembly Pedal Installation Tighten the pedals ﬁgReﬂector Brackets Installation Installing Derailleur Guard on some modelsMaintenance Brake System Test the tightness of each Brake ShoeMaintenance Final Brake Adjustment Before Riding Stretching the cable ﬁgCheck tightness of the cantilever mounting Bolt a Center brake shoes on rimMaintenance Final Brake Adjustment Put the brake shoes the correct distance from the rimMaintenance Test the tightness of the cable clamp ﬁgTest the travel of each brake lever Maintenance Shift System Parts of the Shift SystemOperation Operate the shift system as follows Maintenance Shift System These are the higher gear combinations Front Derailleur Adjustments Perform the Rear Derailleur Adjustments if Maintenance Rear Derailleur Adjustments Adjust the Index Shift System ﬁg Maintenance Three-Piece Cranks various models MaintenanceAdjustment Suspension Frame various modelsTo change the suspension Maintenance Tires Inﬂating the TiresRepair and Service Maintenance LubricationWhat When How Lubrication TableMaintenance Reﬂectors Inspection of the BearingsHead Tube Bearings Crank BearingsWarranty Huffy Corporation Limited Warranty What does this Limited Warranty cover?What must you do to keep the Limited Warranty in effect? What is not covered by this Limited Warranty?Warranty For how long does this Limited Warranty last?How do you get service? What will Huffy do?Always Wear Your Helmet When Riding this Product