Hill Climb

Workout Programs (Continued)

gram setup mode step by step as below:

Enter Age

1.The message window will ﬂ ash a message of “ENTER AGE”, then “AGE = XX” with the number blinking.

2.You may press UP or DOWN keys to adjust the age.

3.After age adjustment, the message display will switch to display “PRESS ENTER” to indicate next step. Press ENTER to accept and enter Weight adjustment.

Enter Weight

1.The message window will ﬂ ash a message of “ENTER WEIGHT”, then “WEIGHT = XXX LB” with the number blinking. (WEIGHT = XXX KG” for metric system)

2.You may press UP or DOWN keys to adjust the weight

3.After weight adjustment, the message display will switch to display “PRESS ENTER” to indi- cate next step. Press ENTER to accept and enter Time adjustment.

Enter your workout time:

1.The message window will ﬂ ash a message of “ENTER TIME”, then “TIME = 30 MIN” and the 30 will be blinking.

2.You may press UP or DOWN keys to adjust the time. When the time setting reaches 60 min- utes, the display will show “TIME = 1HR 00MIN” instead.

3.After time adjustment, the message display will switch to display “SET UP COMPLETED”, then “PESS START” to indicate next step. You may press, the ENTER or START/STOP key to begin this program.

Or press the START/STOP key to accept current default values and begin the workout

•Default time = 30 minutes

•Default Intensity level = preset level as shown in dot matrix proﬁ le

•Age and weight will be what was enter and saved in a previous workout

During the Program

Once the Enter or Start key is pressed, the Warm Up will be active. See Warm Up mode section for de- tails.

Main Display

•As soon as the program will begins, the Dot Matrix will activate and the 1st segment of the program’s proﬁ le will start blinking

•If there is a valid Heart rate signal being detected a heart shape will start blinking and the Heart rate graph will light up with the percentage of maximum heart rate.

•The message “Time” will light up in the date display and the Time will start counting down. To switch the data being displayed press the DISPLAY key to select from Time, Calories, Pulse and Distance and to turn on and off the scan function.

Message/Data Display

•As soon as the program begins. The message display will turn into workout data display and display four default data: Time, Level, Pulse & Calories and the LED on top of the Data Display key will be lit.

•Press the “DATA DISPLAY” buttons to switch the display to “RPM, Speed, Distance & Watts”. The LED on the bottom of the key will light up.

900Ub.Sr OM.R1.indd 30-31

Workout Programs (Continued)

Adjustment

•Press UP or DOWN key to adjust the intensity level from L1 to L16. The dot matrix window will up- date the intensity proﬁ le accordingly.

Ending the Program

•When program time is up or START/STOP key is pressed, this program will end and Cool Down will be active.

•The message display will ﬂ ash a message “PROGRAM ENDED”&”COOL DOWN”. See Cool Down for details.

•START/STOP key could be pressed to re-start the Intervals program again.

•START/STOP key could be pressed and held for 2 seconds to skip the Cool Down and activate the Workout Summary immediately.

Pause, Reset, Switch or Save a program

See Console Operating Tips section for details, page 16

Getting Started

The Hill program simulates a hill climbing exercise with a preset hill proﬁ le. The exercise proﬁ le will guide you up over a hill and down the other side.

Beginning the Program

During idle mode, the message window displays a message “SELECT A PROGRAM”. To begin this program, press the HILL CLIMB program key, the LED indicator above it will

light up.

Entering the program

When the message display ﬂ ashes, “HILL CLIMB” and “PRESS ENTER”, it indicates you are about to select the Hill Climb program. Press ENTER Key to enter program setup mode or press the START/ STOP key to skip the set up mode and use default values.

Press ENTER key to enter program set up mode. The message display will take you through the pro- gram setup mode step by step as below: