Center Delay Time Setting
Register the delay time of the sound from the center speaker, comparing to that of the sound from the front speakers.
If the distance from your listening point to the center speaker is equal to that to the front speakers, select 0 ms. As the distance to the center speaker becomes shorter, increase the delay time.
•1 msec increase (or decrease) in delay time corresponds to 11 13/16 inches (30 cm) decrease (or increase) in distance.
•When shipped from the factory, the delay time is set to 0 ms.
On the front panel ONLY:
1. Press SETTING repeatedly until | CT SETTING |
“CTR DELAY” (Center Delay) |
|
appears on the display. |
|
The display changes to show the current setting.
2. Press CONTROL UP 5/DOWN ° CONTROL
|
| Center |
|
|
| ||
Left front | speaker | Right front | |||||
speaker |
|
|
|
| speaker | ||
|
|
|
| ||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
3.0 m
2.7 m
2.4 m
2.1 m
Left rear | Right rear |
speaker | speaker |
to select the delay time of the
DOWN UP
center speaker output (from 0 ms to 5 ms).
Notes:
•Center delay time is not valid for the DVD MULTI playback mode.
•You cannot adjust the center delay time when you have set “CTR SPK” to “NONE.”
Rear Delay Time Setting
Register the delay time of the sound from the rear speakers, comparing to that of the sound from the front speakers.
If the distance from your listening point to the rear speakers is equal to that to the front speakers, select 0 ms. As the distance to the rear speakers becomes shorter, increase the delay time.
•1 msec increase (or decrease) in delay time corresponds to 11 13/16 inches (30 cm) decrease (or increase) in distance.
•Rear delay time for Dolby Digital and DTS Digital Surround is to be set to 5 ms.
•When shipped from the factory, the delay time is set to 5 ms.
On the front panel ONLY:
Ex. Set the center delay time to “1 ms” and the rear delay time to “2 ms.”
Crossover Frequency Setting
Small speakers cannot reproduce the bass sound very well. So, if you have used a small speaker for any of the front, center, and rear channels, this receiver automatically reallocates the bass elements, originally assigned to the channel for which you have connected the small speaker, to another channel (for which you have connected the large speaker).
To use this function properly, you need to set the crossover frequency level according to the size of the small speaker connected.
•If you have selected “LARGE” for all speakers (see page 17), this function cannot be adjusted.
On the front panel ONLY:
1. Press SETTING repeatedly until ECT SETTING
“CROSS OVER” appears on the display.
The display changes to show the current setting.
1. Press SETTING repeatedly until |
ECT SETTING
2. Press CONTROL UP 5/DOWN ° CONTROL
“REAR DELAY” appears on the |
display.
The display changes to show the current setting.
to select the crossover frequency level according to the size of the small speaker connected.
DOWN UP
2.Press CONTROL UP 5/DOWN ° to select the delay time of the rear speaker output (from 0 ms to
15 ms).
Notes:
CONTROL
DOWN UP
•Each time you press the button, the display changes to show the following:
80Hz
100Hz
120Hz
• Use the following comments as reference when adjusting.
80Hz: Select this when the cone speaker unit built in the
•Rear delay time is not valid for the DVD MULTI playback mode.
•You cannot adjust the rear delay time when you have set “REAR SPK” to “NONE.”
speaker is about 4 3/4 inches (12 cm).
100Hz: Select this when the cone speaker unit built in the
speaker is about 3 15/16 inches (10 cm).
120Hz: Select this when the cone speaker unit built in the speaker is about 3 3/16 inches (8 cm).
Note:
Crossover frequency is not valid for the DVD MULTI playback,
5 CH /4 CH Stereo,
18