JVC RX-7001PGD manual Attenuating the Input Signal, Muting the Sound, Reinforcing the Bass

Page 15
BASS BOOST
SOURCENAME

Listening only with headphones

You can listen with the headphones without deactivating both pairs of speakers; however, if you want to use the HEADPHONE mode (see below), you must turn off both pairs of speakers.

1. Connect a pair of headphones to the PHONES jack on the front

panel.

Attenuating the Input Signal

When the input level of the playing source is too high, the sounds will be distorted. If this happens, you need to attenuate the input signal level to prevent the sound distortion.

English

2. Press SPEAKERS 1 and/or 2 so that no lamps on the buttons are

turned on.

This cancels the surround mode or DSP mode currently selected,

and activates the HEADPHONE mode (see below).

• The HEAD PHONE indicator lights up on the display.

HEADPHONE mode:

This mode can reproduce the LFE channel signals, mixing them with the front channel signals. So you will not miss the subwoofer sounds even if you listen to a source using the

On the front panel ONLY:

Press and hold INPUT ATT. (SOUND SELECT) so that the ATT indicator lights up on the display.

Each time you press and hold the button, the Input Attenuator mode turns on (“INPUT ATT ON”) or off (“INPUT NORMAL”).

Notes:

SOUND SELECT

INPUT ATT.

headphones.

Notes:

While in the HEADPHONE mode, you cannot use any other DSP modes (see page 21.)

Activating the speaker cancels the headphones mode and turns on the DSP mode previously selected.

CAUTION:

Be sure to turn down the volume before connecting or putting on headphones, as high volume can damage both the headphones and your hearing.

Muting the Sound

From the remote control ONLY:

Press MUTING to mute the sound through all

MUTING

 

speakers and headphones connected.

“MUTING” appears on the display and the volume turns off (the volume level indicator goes off).

To restore the sound, press MUTING again so that “OFF” appears on the display.

Turning MASTER VOLUME on the front panel or pressing VOLUME +/– on the remote control also restores the sound.

Reinforcing the Bass

You can boost the bass level.

On the front panel ONLY:

Press BASS BOOST (SOURCE NAME) briefly to select the bass boost function.

• Each time you press the button, the bass boost function turns on (“BASSBOOST ON”) and off (“BASSBOOST OFF”).

Select “BASSBOOST ON” to activate the bass boost function. The BASS BOOST indicator lights up on the display.

Select “BASSBOOST OFF” to cancel it.

The indicator goes off.

Note:

This function affects the front speaker sounds only.

This function is available only for the sources connected using the analog terminals.

This function takes effect when the DSP mode is in use.

When selecting “DVD MULTI” as the source, this effect does not work.

Adjusting the Subwoofer Output Level

You can adjust the subwoofer output level if you have selected “YES” for the “SUBWOOFER” (see page 14).

Once it has been adjusted, the receiver memorizes the adjustment.

Before you start, remember....

There is a time limit in doing the following steps. If the setting is canceled before you finish, start from step 1 again.

When the front speakers are all deactivated, the subwoofer level cannot be adjusted.

On the front panel:

1. Press (BALANCE/) SURROUND

BALANCE/SURROUND

ADJUST repeatedly until

ADJUST

 

“SUBWFR LEVEL” appears on

 

the display.

 

The display changes to show the current setting.

2.

Turn MULTI JOG to adjust the

MULTI JOG

 

subwoofer output level (–10 dB to

 

 

+10 dB).

 

From the remote control:

 

1.

Press SOUND.

SOUND

 

The 10 keys are activated for sound adjustments.

2. Press SUBWOOFER –/+ to adjust

the subwoofer output level (–10 dB

 

 

SUBWOOFER

 

 

 

to +10 dB).

0

+10

 

FM MODE

100+

12

Image 15
Contents RX-7001PGD Precaución English Español Português Table of Contents Parts Identification Remote Control Front PanelSetting the Voltage Selector Switch Before InstallationChecking the Supplied Accessories Connecting the FM and AM AntennasAM Antenna Connections Connecting the SpeakersBasic connecting procedure Connecting the front speakersAbout the speaker impedance Connecting Audio/Video ComponentsConnecting the rear and center speakers Connecting the subwoofer speakerMD recorder To audio output CD playerVideo component connections To audio input Cassette deck To audio outputDBS tuner When you connect the DVD player with stereo output jacksDVD player To composite video input To S-video inputCD player MD recorder Digital connectionsMD recorder, etc DBS tuner DVD playerR6PSUM-3/AA15F Connecting the Power CordPutting Batteries in the Remote Control Plug the power cord into an AC outletSelecting the Source to Play Turning the Power On and Off StandbyFrom the remote control Basic OperationsTurn Source Selector to Adjusting the VolumeSelecting the Front Speakers EtcReinforcing the Bass Attenuating the Input SignalAdjusting the Subwoofer Output Level Muting the SoundChanging the Source Name Basic SettingsAdjusting the Front Speaker Output Balance Recording a SourceRear Delay appears on Display Setting the Subwoofer InformationSetting the Speakers for the DSP Modes Press Setting repeatedly untilLFE ATT Low Frequency Effect Attenuator appears on Display Delay time of the rear speaker OutputTurn Multi JOG to select Crossover FRQ Crossover Frequency appears on the displaySelecting the Analog or Digital Input Mode Digital Input Digital in Terminal SettingSetting the AM Tuner Interval Spacing Using the Sleep TimerShowing the Text Information on Display Tuning in Stations Manually Using Preset TuningReceiving Radio Broadcasts Selecting the FM Reception Mode Assigning Names to Preset StationsSEA level of the selected frequency Range Using the SEA ModesSelecting Your Favorite SEA Mode Creating Your Own SEA Mode Press SEA Adjust repeatedlyUsing the DSP Modes 3D-PHONIC modesDAP modes Surround modes DVD Multi Playback ModeFront Available DSP Modes According to the Speaker ArrangementAdjusting the DAP Modes Adjusting the 3D-PHONIC ModesAdjusting the Surround Modes JVC Theater Surround adjustments Ù PRO Logic and DSP indicators also light up on the displayRepeatedly until Theater To enjoy Dolby Pro Logic, play back a software encoded with To cancel the Dolby/DTS/MPEG Surround modeActivating the DSP Modes Select and play a sound sourceFor the other DSP modes Repeatedly until the DSP mode youTo cancel the DSP mode Want appears on the displayPress DVD Multi so that DVD Using the DVD Multi Playback ModeActivating the DVD Multi Playback Mode DVD Multi appears on DisplayPress %/ Þto move to Visual Using the On-Screen MenusWhen you finish, press Exit Press Menu@/ # Press %/ Þto move to Sound CONTROL, then press @/ #Press %/ Þto move to Surround LEVEL, then press @/ # Adjusting the DVD Multi Playback ModeSelecting Your Favorite SEA Mode Creating Your Own SEA ModeSetting the Basic Setting Items Also see Press %/ Þ/ @/ #to adjust the SEA mode as you wantPress SET to store the setting into the SEA Usermode Press %/ Þto move To SETTING, then press @/ #Storing the Preset Stations Also see Assigning Names to Preset StationsPress %/ Þ / @/ #to Move in front of a character you want Automatic Source Selection Compu Link Remote Control SystemRemote Control through the Remote Sensor on the Receiver Same timeDisc Title Input Text Compu Link Remote Control SystemDisplaying the Disc Information on the TV screen Disc Search Only for CD PlayerDisc Information screen appears on the TV Press Text Display while CD or MD is selected as the sourceShowing the Disc Information on the TV Screen To exit from the Disc information screenPress SET again Press Text Display while CD is selected as the sourcePress %/ Þto move to SEARCH, then Press SET Press %/ Þto move to Performer Then press SETEntering the Disc Information Press %/ Þto move to Search Then press SETPress %/ Þto move To GENRE, then Press SET Press %/ Þto move To Title INPUT, then press SETPress %/ Þto move to Title Input Then press SET Press Text Display while MD is selected as the sourceEnter the disc title Referring to steps 3 Press %/ Þto move to the genre you want, then press SETCase 4 If only the DVD player is equipped with the S AV Compu Link Remote Control SystemIf the AV Compu Link terminal On the TV is RECEIVER/AMPOne-Touch DVD Play Automatic Selection of TV’s Input ModeAutomatic Power On/Off One-Touch Video PlaySound control section Amplifier Operating JVC’s Audio/Video ComponentsOperating Audio Components TunerCassette deck CD player-changer7/P TurntableOperating Video Components DVD player0, 100+ Try to operate your TV by pressing TV/CATV DBS If there are more than one code listed for your brand of TVOperating Other Manufacturers’ Video Equipment Release TV/CATV/DBS10, 0, 100+ +10 If there are more than one code listed for your brandRelease VCR Try to operate your VCR by pressing VCRManufacturers’ codes for TV Manufacturers’ codes for Catv converters Manufacturers’ codes for DBS tuner SEI Problem Possible Cause Solution TroubleshootingVideo SpecificationsAmplifier AudioGeneral Tuning Range Usable Sensitivity Signal-to-Noise RatioFM tuner IHF AM tunerPrecaução para a ligação à tensão da rede CA Precaución para la línea de la red CA

RX-7001PGD specifications

The JVC RX-7001PGD is an outstanding audio receiver that combines exceptional performance with a range of modern features, making it an ideal choice for home theater enthusiasts and music lovers alike. Designed to deliver rich, immersive sound, this receiver is packed with vital technologies that enhance audio fidelity while providing convenience and connectivity options.

One of the standout features of the RX-7001PGD is its robust power output, capable of driving multiple speakers with high clarity and minimal distortion. With multiple channels, it supports surround sound formats, making it perfect for creating an exhilarating home theater experience. Whether you're watching movies or listening to music, this receiver ensures that every note and dialogue is heard with precision and depth.

The device supports various audio formats, allowing users to enjoy their media in the best quality available. From standard stereo to more complex multichannel audio formats, the JVC RX-7001PGD handles it all, providing users with the flexibility to enjoy their favorite content as intended by the creators. Additionally, the receiver features built-in digital signal processing, which helps optimize audio playback for different environments, ensuring a balanced listening experience regardless of the room's acoustics.

In terms of connectivity, the RX-7001PGD excels with multiple input options including HDMI, optical, and analog connections, allowing seamless integration with a variety of devices such as televisions, gaming consoles, and Blu-ray players. With USB support, users can easily connect their music libraries directly to the receiver, making it easier than ever to enjoy playlists without the need for additional equipment.

The receiver also includes Bluetooth technology, enabling wireless streamlining from smartphones and tablets, so users can enjoy their favorite tracks without the hassle of cables. This feature enhances the receiver's versatility, making it not only a powerful audio component but also a hub for a modern multimedia setup.

Furthermore, the JVC RX-7001PGD has an intuitive user interface, making setup and operation straightforward even for those who are not tech-savvy. The included remote control is comprehensive, providing easy navigation between settings and sources.

Overall, the JVC RX-7001PGD offers an impressive combination of power, versatility, and modern technology, making it a compelling choice for anyone looking to build or upgrade their home audio system. With its engaging sound quality and user-friendly design, this receiver stands out in the crowded marketplace of home theater receivers.