JVC RX-7001PGD manual Setting the Subwoofer Information, Setting the Speakers for the DSP Modes

Setting the Subwoofer Information

Register whether or not you have connected a subwoofer.

Before you start, remember...

•There is a time limit in doing the following steps. If the setting is canceled before you finish, start from step 1 again.

On the front panel ONLY:

SETTING

1.Press SETTING repeatedly until “SUBWOOFER” appears on the

display.

The display changes to show the current setting.

MULTI JOG

2.Turn MULTI JOG to register whether you have connected a subwoofer or not.

•As you turn it, the subwoofer setting alternates between “YES” and “NO.”

3.Repeat steps 1 and 2 to select the appropriate items for the other speakers.

Notes:

•Keep the following comment in mind as reference when adjusting.

–If the size of the cone speaker unit built in your speaker is greater than 12 cm, select “LARGE,” and if it is smaller than 12 cm, select “SMALL.”

•If you have selected “NO” for the subwoofer setting, you can only select “LARGE” for the front speaker setting.

•If you have selected “SMALL” for the front speaker setting, you cannot select “LARGE” for the center and rear speaker settings.

Center Delay Time Setting

Register the delay time of the sound from the center speaker, comparing to that of the sound from the front speakers.

If the distance from your listening point to the center speaker is equal to that to the front speakers, select 0 msec. As the distance to the center speaker becomes shorter, increase the delay time.

•1 msec increase (or decrease) in delay time corresponds to 30 cm decrease (or increase) in distance.

•When shipped from the factory, delay time is set to 0 msec.

English

YES: Select this when a subwoofer is used. SUBWFR lights up on the display (see page 11).

NO: Select this when no subwoofer is used.

Setting the Speakers for the DSP Modes

On the front panel ONLY:

1. Press SETTING repeatedly until “CENTER DELAY” appears on the display.

SETTING

To obtain the best possible surround sound of the DSP modes, you have to register the information about the speakers arrangement after all connections are completed.

Before you start, remember...

•There is a time limit in doing the following steps. If the setting is canceled before you finish, start from step 1 again.

Front, Center, and Rear Speaker Setting

Register the sizes of all the connected speakers.

•When you change your speakers, you need to register the information about the speakers again.

On the front panel ONLY:

1. Press SETTING repeatedly until	SETTING
“FRONT SPK” (Front Speaker),
“CENTER SPK” (Center
Speaker) or “REAR SPK” (Rear
Speaker) appears on the display.
The display changes to show the current setting.
	MULTI JOG

2.Turn MULTI JOG to select the appropriate item about the speaker selected in the above step.

• As you turn it, the display changes to show the following:

LARGE SMALLNONE

LARGE: Select this when the speaker size is relatively large.

SMALL: Select this when the speaker size is relatively small.

NONE: Select this when you have not connected a speaker. (Not selectable for the front speakers.)

The display changes to show the current setting.

MULTI JOG

2.Turn MULTI JOG to select the delay time of the center speaker output.

•Turn it clockwise to increase the delay time from 0 msec (“C. DELAY: 0ms”) to 5 msec (“C. DELAY: 5ms”).

•Turn it counterclockwise to decrease the delay time from

5 msec (“C. DELAY: 5ms”) to 0 msec (“C. DELAY: 0ms”).

Notes:

•Center delay time setting is not valid for the DVD MULTI playback mode.

•You cannot adjust the center delay time when you have set “CENTER SPK” to “NONE.”

Rear Delay Time Setting

Register the delay time of the sound from the rear speakers, comparing to that of the sound from the front speakers.

If the distance from your listening point to the rear speakers is equal to that to the front speakers, select 0 msec. As the distance to the rear speakers becomes shorter, increase the delay time.

•1 msec increase (or decrease) in delay time corresponds to 30 cm decrease (or increase) in distance.

•Rear delay time for Dolby Digital, DTS Digital Surround and MPEG Multichannel is to be set to 5 msec.

•When shipped from the factory, delay time is set to 5 msec.

On the front panel ONLY:

1. Press SETTING repeatedly until	SETTING
“REAR DELAY” appears on the
display.

The display changes to show the current setting.

14