23. Wrap the Butterfly Cable (89) around a 3 1/2Ó Pulley | 23 |
| Wide Tab |
| |||
(82) as shown. Attach the Pulley and two Pulley |
|
| |||||
|
|
| |||||
|
|
|
|
| |||
Covers (94) to the bracket on the | Wide Tab |
|
|
|
|
| 42 |
Leg Press Upright (4) with a |
|
| 99 |
| 94 | ||
|
| 4 | |||||
3/8Ó x 2 1/4Ó Bolt (99), a 3/8Ó |
|
| |||||
| on Cable |
|
|
| |||
Washer (38) and a 3/8Ó Nylon |
|
|
|
|
| ||
94 |
|
|
|
|
|
| |
Locknut (42). The Pulley Covers |
|
|
|
|
|
| |
|
|
|
|
|
|
| |
must be oriented as shown in |
|
|
|
| 38 |
|
|
the inset drawing. Note that the |
|
|
|
| 94 |
| |
|
|
|
|
|
| ||
wide tab is over the stress- |
|
|
|
|
| 82 |
|
point, where the Cable wraps |
| 82 |
|
|
|
|
|
around the Pulley. Use this ori- |
|
|
|
|
|
| |
entation of the Pulley Covers in |
|
|
|
|
| 89 |
|
the following assembly steps. |
|
|
|
|
|
|
|
24. Locate one of the preassembled pairs of Pulley | 24 |
|
|
|
| ||
Plates (31) and remove both 3 1/2Ó Pulleys (82). |
|
|
|
| |||
|
|
| 89 |
| |||
|
|
|
|
|
|
| |
Route the Butterfly Cable (89) around a 3 1/2Ó Pulley |
|
|
|
|
| ||
(82) in the direction shown. Attach the Pulley and two |
|
|
|
|
| ||
Pulley Covers (94) to the Pulley Plates (31) with a |
|
|
|
|
| ||
3/8Ó x 2 1/4Ó Bolt (99) and a 3/8Ó Nylon Locknut (42). |
| 94 | 82 | 94 |
| ||
Note: The end of the Pulley Plates (31) with two |
|
| |||||
|
|
|
|
| |||
holes should be pointed downward. Orient the |
|
|
| 99 |
| ||
wide tab on the Pulley Covers as shown. |
| Wide Tab |
|
|
| ||
|
|
|
|
| End with | ||
|
|
|
| 42 |
| two holes | |
|
|
|
|
| should be | ||
|
|
|
|
|
|
| |
|
|
|
|
| 31 |
| down |
|
|
|
|
|
|
| |
25. Wrap the Butterfly Cable (89) around a 3 1/2Ó Pulley | 25 |
|
| Wide Tab |
| ||
(82) as shown. Attach the Pulley and two Pulley |
|
|
| ||||
|
|
|
| ||||
|
|
|
|
| |||
Covers (94) to the other side of the bracket on the Leg | 99 | |
Press Upright (4) with a 3/8Ó x 2 1/4Ó Bolt (99), a 3/8Ó | 82 | |
38 | ||
Washer (38) and a 3/8Ó Nylon Locknut (42). Orient | ||
| ||
the wide tab on the Pulley Covers as shown. | 89 | |
42 | ||
| 94 | |
| 4 |
26.Note: The Left Arm (6) is shown removed for easi- er part identification. Insert a 5/16Ó x 1Ó Bolt (97) through the bracket on the Left Arm. Fully tighten a 5/16Ó Nylon Jam Nut (91) onto the Bolt.
Slide the free end of the Butterfly Cable (89) onto the 5/16Ó x 1Ó Bolt (97). Thread another 5/16Ó Nylon Jam Nut (91) onto the Bolt, but do not fully tighten it.
Leave enough room between the two Jam Nuts for the Cable to pivot.
26
91
89
976
12