Whirlpool 3396304 Electrical power, Open lint screen lid. Remove two screws, At rear, View a

Page 19

lf your dryer Is gas and has a full front panel, remove tront panel as follows:

1. Unplug the power supply cord or turn off the

electrical power.

2. Open lint screen lid. Remove two screws

from lint screen area.

3. Open top by pulling forward and up at each

front comer (see View A). Rest raised top

against wall behind dryer (top is hinged

at rear).

4

Remove screws before opening top

4. Remove two internal screws from front

panel flanges (near top front corners). Lift

front panel slightly, lifting off lower clips (see

View B). Slowly pull front panel forward,

disengaging panel from drum. (Drum will

drop slightly.)

5. Move front panel aside and rest edge

against side of dryer. Avoid disconnecting

wire clips (see View C) or damaging wires.

6. Remove lint from area shown in “gasdryer’

illustration on page 18 with soft brush or

vacuum cleaner. Avoid damaging wires,

funnel or ignitor.

7. Reassemble in reverse order. Before

closing the top, check the following:

View A

Drum seal

Side panel

-Drum seal must be flared out (see View

D)and properly positioned against panel at back of drum. Rotate drum counter- clockwise one full turn to check drum seal.

-Belt should be centered and tight on dryer drum.

-Wire clips which hold the door switch wires must be anchored in slot in top of front panel (see View C) and along top edge of side panel. Door wire.s must not touch drum when dryer is operating. See Warning, page 18.

6.Replace top panel and lint screen screws. Top and front panels must be securely in place before operating dryer.

9.Reconnect power and level dryer again (if necessary).

4t

View B

Wire clip- holds door switch wires

NOTE: Call our Consumer Assistance Center at l-800-253-1301 for assistance or more information.

View D

Image 19
Contents Electronicgas and Electricdryers Purchase Date Your safety is important to usThank you for buying a Whirlpool@ appliance Serial Number DealerWhat to do if YOU Smell GAS Understanding SafetyUnderstanding your responsibilities Important Safety InstructionsOther features not shown FeaturesUser Cards One tone if the dryer accepts your selection Using the electronic touch controlsBefore starting your dryer This SectionYour dryer Stopping and restartingCydesITemps Press Select Using Automatic dryingUntil the light glows by the CycleITemp desired Using Timed dryingTo select a different cycle/ temp Selecting cycles/tempsPress ON/SELECT until the light glows by Cotton and Llnens Cycle chartRubber, Plastic or Heat Sensltlve items Fluff Air-No HeatSee Warning on Options Using Your Options/FeaturesUsing Cycle Signal Finish Guard Options Option Selection ChartTo lock/unlock control panel Using the Lockout featureUnderstanding the Finish Guard cycle Status LightsCaring For Your Dryer Maintenance-every loadCleaning the lint screen Lint signalCleaning the dryer exterior Maintenance-as neededCleaning a clogged lint screen Cleaning the dryer interiorElectrIcal Shock and Fire Hazard Changing the drum lightRemoving accumulated lint Vacuum cleaner. Avoid damaging wires Electrical powerAgainst side of dryer. Avoid disconnecting Wire clips see View C or damaging wiresSorting Before you dryThis Drying tipsPillows, stuffed toys Drying special-care itemsDlapers, baby clothes Elastic Items Saving energy Using dryer fabric softenersVacation care Enough Detergent Was used Solving laundering problemsWere Dried Llnt Lint screen is clogged Load Is properly Duct or outside To Installation Instructions Lint screenMoisture in the load to be Below 45F 7C DryerBefore calling for assistance If You Need Assistance Or ServiceIs the dryer door firmly closed? If you need assistance If you need service’If you are not satisfied with how the problem was solved ’ When asklng for help or servlceDefective in materials or workmanship Full ONE-YEAR WARRANlY From Date of Purchase