Whirlpool 3396304 Moisture in the load to be, Below 45F 7C Dryer, Duct or outside, Hood, Is used

Page 25

PROBLEM

CHECK IF

Shrlnklng

Items are overdried

Fabric type and quality is suitable for drying

Slow drying

There

is a large amount

of

 

moisture in the load to be

 

dried

 

 

 

 

 

 

 

Cold rinse water is used

 

 

Room air temperature

is

 

below 45°F (7°C)

 

 

 

Dryer

is exhausted according

 

to Installation

Instructions

 

Lint screen

is clogged

 

 

 

Exhaust

duct or outside

 

 

exhaust

hood

is clogged

 

 

Proper

electrical supply

is

 

used

 

 

 

 

 

 

Static

Load

is overdried

 

 

electrlclty

 

 

 

 

 

 

 

 

Fabric

softener

is used

 

 

Synthetics,

synthetic

blends,

permanent press and knits are in load

CAUSES/SOLUTIONS

Remove items while there is still a trace of moisture. Some items should be removed while damp, then shaped and air dried.

Some knits are stretched during manufac- turing. Washing and drying returns them to the original size. This is normal. Check quality of garment before buying. Follow fabric care label directions carefully.

Some items hold more moisture than others (cottons more than polyester). They take longer to dry. Full loads take longer to dry than small loads of the same fabric.

A load rinsed in cold water will take slightly longer to dry than a warm one. Cold rinses, however, help save energy and reduce wrinkling more than warm rinses do.

Install dryer in a room where the air temperature is warmer than 45°F (7°C). Cold air increases drying time and may cause wrinkles not to be removed.

Install and exhaust your dryer according to the Installation Instructions provided.

Clean lint screen before or after each use.

Clean if needed.

Properly connect the dryer to a grounded electrical circuit that meets the electrical requirements stated in the Installation Instructions.

Remove items while there is still a trace of moisture.

Use a fabric softener and follow package directions carefully.

Synthetics, synthetic blends, permanent press and knits build up static electricity. Use a fabric softener and be careful not to overdry the load.

25

Page 24 Page 26
Image 25
Page 24 Page 26
Contents Electronicgas and Electricdryers Thank you for buying a Whirlpool@ appliance Your safety is important to usSerial Number Dealer Purchase DateWhat to do if YOU Smell GAS Understanding SafetyUnderstanding your responsibilities Important Safety InstructionsOther features not shown FeaturesUser Cards Before starting your dryer Using the electronic touch controlsThis Section One tone if the dryer accepts your selectionYour dryer Stopping and restartingCydesITemps Press Select Using Automatic dryingUntil the light glows by the CycleITemp desired Using Timed dryingTo select a different cycle/ temp Selecting cycles/tempsPress ON/SELECT until the light glows by Cotton and Llnens Cycle chartRubber, Plastic or Heat Sensltlve items Fluff Air-No HeatSee Warning on Using Cycle Signal Finish Guard Options Using Your Options/FeaturesOption Selection Chart OptionsUnderstanding the Finish Guard cycle Using the Lockout featureStatus Lights To lock/unlock control panelCleaning the lint screen Maintenance-every loadLint signal Caring For Your DryerCleaning a clogged lint screen Maintenance-as neededCleaning the dryer interior Cleaning the dryer exteriorElectrIcal Shock and Fire Hazard Changing the drum lightRemoving accumulated lint Against side of dryer. Avoid disconnecting Electrical powerWire clips see View C or damaging wires Vacuum cleaner. Avoid damaging wiresThis Before you dryDrying tips SortingPillows, stuffed toys Drying special-care itemsDlapers, baby clothes Elastic Items Saving energy Using dryer fabric softenersVacation care Enough Detergent Was used Solving laundering problemsWere Dried Llnt Lint screen is clogged Load Is properly Moisture in the load to be To Installation Instructions Lint screenBelow 45F 7C Dryer Duct or outsideBefore calling for assistance If You Need Assistance Or ServiceIs the dryer door firmly closed? If you are not satisfied with how the problem was solved If you need service’’ When asklng for help or servlce If you need assistanceDefective in materials or workmanship Full ONE-YEAR WARRANlY From Date of Purchase
Top Page Image Contents