JVC TH-A104 manual Analog connections, Video component connections, Analog component connections

Page 10

Connections

Connecting Audio/Video Components

You can connect the following audio/video components to this system.

Refer also to the manuals supplied with your components. Audio Components: Cassette deck or MD recorder* Video Components: TV or DBS tuner*

VCRs

*You can connect these components using the methods described in “Analog connections” (see below) or in “Digital connections” (see page 9).

Analog connections —————————————

Analog component connections

Use the cable with RCA pin plugs (not supplied).

Connect the white plug to the audio left jack, and the red plug to the audio right jack.

CAUTION:

If you connect a sound-enhancing device such as a graphic equalizer between the source components and the center unit, the sound output through this system may be distorted.

Cassette deck or MD recorder

MD recorder

To audio input To audio output

To audio input To audio output Cassette deck

Notes:

•When the DSP mode is ON, the VCR OUT (REC) jack and the TAPE/MD OUT (REC) jack will output surround sound to the front speakers only.

When recording, turn the DSP mode OFF (see page 21).

•You can connect either a cassette deck or a MD recorder to the TAPE/MD jacks. When connecting a MD recorder to the TAPE/ MD jacks, change the source name, which will be shown on the display when selected as the source, to “MD”. See page 17 for details.

If your audio components have a COMPU LINK-3 terminal

•See also page 54 for detailed information about the connection and the COMPU LINK-3 remote control system.

Video component connections —————————

Use the cable with RCA pin plugs (not supplied).

Connect the white plug to the audio left jack, the red plug to the audio right jack, and the yellow plug to the composite video jack. If your video components have S-video (Y/C-separation) terminals, connect them using S-video cable (not supplied).

Connecting these video components through the S-video input/ output terminal will give you better picture playback (or recording) quality.

IMPORTANT

This system is equipped with both the composite video and S-video input/output terminals for connecting video components.

You do not have to connect both the composite video and S-video terminals.

However, remember that the video signals from the composite video input terminals are output only through the composite video out terminals, while the ones from the S-video input terminals are output only through the S-video output terminals.

Therefore, if a recording video component and a playing video component are connected to the center unit through the different video terminals, you cannot record the picture from the playing component on the recording component. In addition, if the TV and a playing video component are connected to the center unit through the different video terminals, you cannot view the playback picture from the playing component on the TV.

VCR

To left/right

 

channel audio S-VHS (or VHS) VCR

To composit

input

video output

To left/right

To composit

channel audio

video input

output

 

To S-video

To S-video

input

output

8

Page 9 Page 11
Image 10
Page 9 Page 11
Contents TH-A10 Class Laser Product Table of Contents Getting Started Safety precautionsChecking the supplied accessories Important cautionsRear left speaker System outlineCenter speaker SP-XCA10 Front left speaker Front right speakerSpeaker InstallationAdjusting the angle of the satellite speakers To hang satellite speakers from the wallDisc structure About discsPlayable disc types Video CDs or SVCDs with Playback Control functionAM antenna connections Connecting the TVConnections FM antenna connectionsTo connect speakers Connecting the rear and center speakersConneceting the front speakers Analog component connections Analog connectionsVideo component connections If your audio components have a Compu LINK-3 terminalDigital connections TV audio or DBS tunerPlug the power cord into an AC outlet Connecting the power cordLight up the primary remote control buttons Center unit Power sub wooferCenter unit Powered sub wooferParts Identification Display windowRemote controls Primary remote controlOperation with the remote control Principles of operationOn-screen menu components To operate via the on-screen menuDisplaying the on-screen menu Basic operation with the on-screen menuPreventing screen burn-out with Screen saver Screen Saver On-screen menus On-screen menus for using discsOn-screen menus for setting up the DVD Opening screens VCD Control displayAdjusting volume To turn the system power supply On and OFF standbyTo turn TV power on and OFF Basic operationsChanging the source name Muting the soundSelecting the source to play Press one of the source selecting buttonsSelecting the analog or digital input Mode Changing the decode modeSub woofer volume control Phase setting Adjusting the Input Signal LevelAudio channel display lamp Press Sleep repeatedly Using the Sleep TimerUsing the DSP Modes To check or change the time remaining until Shut-off timeWhen selecting DAP Press DSP ModeBefore recording a digital source, turn off the DSP mode DAP modesUsing the DVD player To play a discPausing Locating the beginningPress ¢or Resuming playbackSelecting playback from the DVD menu Press Resume during playbackPress Return to return to the menu screen When appears on the TV screenSelecting 11 or higher To specify the time for playback To play from the beginning of a title Chapter, or trackTo specify the chapter number for Playback CHAP. Search Press DVD on ScreenPress Digest To select the screen for playback from Digest screen DigestUse the number buttons 0 ~ 9 to enter the time Press Pause at the section you wish to view in slow motion Slow-Motion Playback SlowTo display Continuous Photos Strobe Hold down FF/¢or 4/REW for more than 2 secondsChanging the Subtitle Language Using the Subtitle buttonZooming a scene Zoom Press ZoomUse the 2/3cursors to select the desired subtitle Changing the audio channel AudioUse the 5/∞cursors to move the pointer Subutitle Use the 5/∞cursors to move the pointer to AudioUse the 2/3cursors to select the desired angle number Press and hold Angle for more than 1 secondsSelecting a scene angle from the on-screen display Selecting an angle from the angle list displaySelecting the Picture Character Or all tracks RepeatSampling all tracks Intro Programming the Playing Order Tracks Program Use the 5/∞cursors to move the pointer to Time SelectUse the 5/∞cursors to move the pointer Random Random Play RandomPress Play to start program play Quitting programmed playbackTuning in stations manually Setting the AM tuner interval spacingReceiving radio broadcasts Press FM Mode Selecting the FM reception modeWhen an FM stereo broadcast is hard to receive or noisy Beat cutMain Menu Performing miscellaneous settingsDVD settings on-screen display Sound Menu Speaker MenuSetting the Sleep Timer Main Menu SettingsOpening the Main Menu Adjusting the volume Changing the DSP ModeMove the pointer to Decode Mode using the 5/∞ cursors Using Loudness Sound Menu SettingsAdjusting the balance Opening the Sound MenuAdjusting input signal Adjusting the DSP effectSwitching speaker mode Speaker Menu SettingsOpening the Speaker Menu Set speaker size Setting speaker sizeUse the 2/3cursors to select Speaker Size Speaker parametersAdjusting delay time Adjusting delay timeAdjust speaker level After adjusting speaker levelsChoosing menu language DVD Menu SettingsOpening the DVD Menu Change source to DVD, and stop playbackChoosing audio language On-screen guide settingsMove the pointer to Audio Language using Choosing subtitle languageLB Letter Box Conversion Screen saver settingsSelect monitor type PS Pan-scan ConversionParental lock level Limiting playback by childrenUse the 5/∞cursors to move the pointer to Buttons 0 ~To temporarily release the Parental lock To change the settingsEnter your 4-digit password using the number buttons 0 ~ YES or NO, then press EnterCare and handling of discs How to handle discsMaintenance of discs Label sideConnections AV Compu Link Remote Control SystemTo Video input Remote control of the TV and VCR using this remote control Automatic Selection of TV’s Input ModeAutomatic Power On/Off When system power is onRemote Control through the Remote Sensor on the center unit Compu Link Remote Control SystemAutomatic Source Selection To operate JVC’s video components using this remote control To operate JVC’s audio components using this remote controlOperating JVC’s Audio/Video Components VCR Cassette deckMD recorder TV VOL +Release TV/CATV/DBS Enter manufacturer’s code two digits usingPress TV/DBS Press and holdTry to operate your VCR by pressing VCR Pressing TV/CATV/DBSPress VCR ReleaseTroubleshooting Problem Possible Cause SolutionCenter unit XV-THA10 SpecificationsPowered Sub-woofer SP-PWA10 Satellite Speakers SP-XSA10Appendix a Table of languages and their abbreviations Appendix B Country code list for parental lock Page EN. SP 0900TNMNATJSC Non-slip rubber Satellite speaker rear right speaker Powered sub-wooferSatellite speaker Center speaker Front left stpeker Satellite speaker rear left speakerAjuste del ángulo de los altavoces satélite
Top Page Image Contents