JVC TH-A104 manual Adjusting delay time, Adjust speaker level, Stop test tone playback

Page 47
See page 43, “Opening the SPEAKER MENU”.
2. Switch the speaker mode to EXPERT.
3. Move the pointer to the speaker selection box using the 5/∞cursors.
Use the 2/3cursors to select SPEAKER LEVEL.
Open the SPEAKER MENU.
1.
Setting speaker level

Pressing the 2/3cursors switches between the following settings.

jSPEAKER SIZEjSPEAKER LEVELjDELAYj

4. Play a test tone (only when the DSP mode is set to “SURROUND ON” or “THEATER”).

Using the 5/∞ cursors, move the pointer to TEST TONE and press ENTER.

Notes:

•The speaker level can be set without playing a test tone.

•Speakers with speaker size set to OFF will not play a test tone.

5.Adjust speaker level.

Use the 5/∞cursors to move the pointer to the parameter you wish to set. Then adjust the level using the 2/3cursors.

The Note icon on the screen indicates the selected speaker.

Note icon

 

Adjustable

 

parameters

C.SP

: Adjust center speaker level.

R.L. SP

: Adjust left rear speaker level.

R.R. SP

: Adjust right rear speaker level.

SUB WOOFER

: Adjust sub-woofer level.

•Each speaker level can be adjusted from –10 dB to +10 dB.

•Speakers marked with a “ – – ” cannot be adjusted.

•The F. SP (Front Speaker) level cannot be adjusted.

•You can save center speaker and rear speaker adjustments for each DSP mode and save them in memory.

After adjusting speaker levels

6. Stop test tone playback.

Use the 5/∞cursors to move the pointer to TEST TONE and press ENTER.

SPEAKER MENU Settings

Adjusting delay time

The delay time for the center speaker and rear speakers is calculated by comparing the distance between the rear/center speakers and the listening point with the distance between the front speakers and the listening point.

1. Open the SPEAKER MENU.

See page 43, “Opening the SPEAKER MENU”.

2. Switch the speaker mode to EXPERT.

3. Move the pointer to the speaker selection box using the 5/∞cursors.

Use the 2/3cursors to select DELAY.

Pressing the 2/3cursors switches between the following settings.

jSPEAKER SIZEjSPEAKER LEVELjDELAYj

4. Adjusting delay time.

Use the 5/∞cursors to move the pointer to the parameter you wish to set. Then adjust the delay time using the 2/3cursors. The Note icon on the screen indicates the selected speaker.

Note icon

– –

Adjustable parameters

C. SP : Adjusts the center speaker delay time. Delay time can be set between 0 ms and 5 ms.

When the distance between the listening point and the center speaker is close to the distance to the front speakers, set the delay time to 0 ms. Increase the delay time when the distance to the center speaker is shorter.

•A 1ms increase/decrease of delay time is equivalent to a 30 cm change in distance.

R.SP : Adjusts the rear speaker delay time.

Delay time can be set between 0 ms and 15 ms. When the distance between the listening point and the rear speakers is close to the distance to the front speakers, set the delay time to 0 ms. Increase the delay time when the distance to the rear speakers is shorter.

•A 1ms increase/decrease of delay time is equivalent to a 30 cm change in distance.

•Speakers marked with a “ – – ” cannot be adjusted.

•“CROSS OVER” has the same effect as setting with “SPEAKER SIZE”.

45

Page 46 Page 48
Image 47
Page 46 Page 48
Contents TH-A10 Class Laser Product Table of Contents Important cautions Safety precautionsChecking the supplied accessories Getting StartedFront right speaker System outlineCenter speaker SP-XCA10 Front left speaker Rear left speakerTo hang satellite speakers from the wall InstallationAdjusting the angle of the satellite speakers SpeakerVideo CDs or SVCDs with Playback Control function About discsPlayable disc types Disc structureFM antenna connections Connecting the TVConnections AM antenna connectionsConneceting the front speakers Connecting the rear and center speakersTo connect speakers If your audio components have a Compu LINK-3 terminal Analog connectionsVideo component connections Analog component connectionsTV audio or DBS tuner Digital connectionsCenter unit Power sub woofer Connecting the power cordLight up the primary remote control buttons Plug the power cord into an AC outletDisplay window Powered sub wooferParts Identification Center unitPrimary remote control Remote controlsPrinciples of operation Operation with the remote controlBasic operation with the on-screen menu To operate via the on-screen menuDisplaying the on-screen menu On-screen menu componentsOpening screens VCD Control display On-screen menus On-screen menus for using discsOn-screen menus for setting up the DVD Preventing screen burn-out with Screen saver Screen SaverBasic operations To turn the system power supply On and OFF standbyTo turn TV power on and OFF Adjusting volumePress one of the source selecting buttons Muting the soundSelecting the source to play Changing the source nameChanging the decode mode Selecting the analog or digital input ModeAudio channel display lamp Adjusting the Input Signal LevelSub woofer volume control Phase setting To check or change the time remaining until Shut-off time Using the Sleep TimerUsing the DSP Modes Press Sleep repeatedlyDAP modes Press DSP ModeBefore recording a digital source, turn off the DSP mode When selecting DAPTo play a disc Using the DVD playerLocating the beginning PausingPress Resume during playback Resuming playbackSelecting playback from the DVD menu Press ¢orSelecting 11 or higher When appears on the TV screenPress Return to return to the menu screen Press DVD on Screen To play from the beginning of a title Chapter, or trackTo specify the chapter number for Playback CHAP. Search To specify the time for playbackUse the number buttons 0 ~ 9 to enter the time To select the screen for playback from Digest screen DigestPress Digest Hold down FF/¢or 4/REW for more than 2 seconds Slow-Motion Playback SlowTo display Continuous Photos Strobe Press Pause at the section you wish to view in slow motionPress Zoom Using the Subtitle buttonZooming a scene Zoom Changing the Subtitle LanguageUse the 5/∞cursors to move the pointer to Audio Changing the audio channel AudioUse the 5/∞cursors to move the pointer Subutitle Use the 2/3cursors to select the desired subtitleSelecting an angle from the angle list display Press and hold Angle for more than 1 secondsSelecting a scene angle from the on-screen display Use the 2/3cursors to select the desired angle numberOr all tracks Repeat Selecting the Picture CharacterSampling all tracks Intro Use the 5/∞cursors to move the pointer to Time Select Programming the Playing Order Tracks ProgramQuitting programmed playback Random Play RandomPress Play to start program play Use the 5/∞cursors to move the pointer RandomReceiving radio broadcasts Setting the AM tuner interval spacingTuning in stations manually Beat cut Selecting the FM reception modeWhen an FM stereo broadcast is hard to receive or noisy Press FM ModeSound Menu Speaker Menu Performing miscellaneous settingsDVD settings on-screen display Main MenuOpening the Main Menu Main Menu SettingsSetting the Sleep Timer Move the pointer to Decode Mode using the 5/∞ cursors Changing the DSP ModeAdjusting the volume Opening the Sound Menu Sound Menu SettingsAdjusting the balance Using LoudnessAdjusting the DSP effect Adjusting input signalOpening the Speaker Menu Speaker Menu SettingsSwitching speaker mode Speaker parameters Setting speaker sizeUse the 2/3cursors to select Speaker Size Set speaker sizeAfter adjusting speaker levels Adjusting delay timeAdjust speaker level Adjusting delay timeChange source to DVD, and stop playback DVD Menu SettingsOpening the DVD Menu Choosing menu languageChoosing subtitle language On-screen guide settingsMove the pointer to Audio Language using Choosing audio languagePS Pan-scan Conversion Screen saver settingsSelect monitor type LB Letter Box ConversionButtons 0 ~ Limiting playback by childrenUse the 5/∞cursors to move the pointer to Parental lock levelYES or NO, then press Enter To change the settingsEnter your 4-digit password using the number buttons 0 ~ To temporarily release the Parental lockLabel side How to handle discsMaintenance of discs Care and handling of discsTo Video input AV Compu Link Remote Control SystemConnections When system power is on Automatic Selection of TV’s Input ModeAutomatic Power On/Off Remote control of the TV and VCR using this remote controlAutomatic Source Selection Compu Link Remote Control SystemRemote Control through the Remote Sensor on the center unit Operating JVC’s Audio/Video Components To operate JVC’s audio components using this remote controlTo operate JVC’s video components using this remote control TV VOL + Cassette deckMD recorder VCRPress and hold Enter manufacturer’s code two digits usingPress TV/DBS Release TV/CATV/DBSRelease Pressing TV/CATV/DBSPress VCR Try to operate your VCR by pressing VCRProblem Possible Cause Solution TroubleshootingSatellite Speakers SP-XSA10 SpecificationsPowered Sub-woofer SP-PWA10 Center unit XV-THA10Appendix a Table of languages and their abbreviations Appendix B Country code list for parental lock Page EN. SP 0900TNMNATJSC Satellite speaker rear left speaker Satellite speaker rear right speaker Powered sub-wooferSatellite speaker Center speaker Front left stpeker Non-slip rubberAjuste del ángulo de los altavoces satélite
Top Page Image Contents