References
Maintenance
7Handling Discs
•Remove the disc from its case by holding it at the edge while pressing the center hole lightly.
•Do not touch the shiny surface of the disc or bend the disc.
•Put the disc back in its case after use to prevent warping.
•Be careful not to scratch the surface of the disc when placing it back in its case.
•Avoid exposure to direct sunlight, temperature extremes and moisture.
To clean the disc
Wipe the disc with a soft cloth in a straight line from center to edge.
• DO NOT use any solvent — such as conventional record cleaner, spray, thinner or benzine — to clean the disc.
7Cleaning the system
•Stains on the system should be wiped off with a soft cloth. If the system is heavily stained, wipe it with a cloth soaked in water diluted neutral detergent and wrung well, then wipe clean with a dry cloth.
•Since the system may deteriorate in quality, become damaged or get its paint peeled off, be careful about the following.
•DO NOT wipe it with a hard cloth.
•DO NOT wipe it strong.
•DO NOT wipe it with thinner or benzine.
•DO NOT apply any volatile substance such as insecticides to it.
•DO NOT allow any rubber or plastic to remain in contact with it for a long time.
Troubleshooting
PROBLEM | POSSIBLE CAUSE | SOLUTION | |
|
|
| |
Power does not come | The power cord is not connected. | Connect the power cord correctly. (See page 10.) | |
on. |
|
| |
|
|
| |
The remote control does | The batteries are exhausted. | Replace the batteries. (See page 6.) | |
not work. |
|
| |
Sunlight is falling directly on the remote sensor. | Hide the remote sensor from direct sunlight. | ||
| |||
|
|
| |
The remote control does | The remote control mode is not for the desired source. | Before operation, press one of the source selecting | |
not work as expected. |
| buttons for the desired source. | |
|
|
| |
| The position of the remote control mode selector is | Set the selector to the correct position. | |
| incorrect. |
| |
|
|
| |
No sound. | The speaker cord is not connected. | Check the connection. (See page 8.) | |
|
|
| |
| The audio cord is not connected to AUX IN and/or | Connect the cord correctly. (See page 10.) | |
| DIGITAL IN correctly. |
| |
|
|
| |
| An incorrect source has been selected. | Select the correct source. (See page 14.) | |
|
|
| |
| The decode mode is not set correctly. | Select the proper decode mode. (See page 30.) | |
|
|
| |
No picture is displayed | The video cord is not connected correctly. | Connect the cord correctly. (See page 9.) | |
on the TV screen. |
|
| |
The disc is not playable. | Use a playable disc. (See page 3.) | ||
| |||
|
|
| |
No picture is displayed | The scan mode is set to “NTSC PROG.” though the | Change the scan mode to “PAL” or “NTSC.” (See page | |
on the TV screen, the | center unit is connected to the TV which does not | 15.) | |
picture is blurred, or the | support the progressive video input. |
| |
picture is divided into |
|
| |
two parts. |
|
| |
|
|
| |
Video and audio are | The disc is scratched or dirty. | Replace or clean the disc. | |
distorted. |
|
| |
A VCR is connected between the center unit and the | Connect the center unit and TV directly. (See page 9.) | ||
| |||
| TV. |
| |
|
|
| |
The picture does not fit | The monitor type is not set correctly. | Set “MONITOR TYPE” properly. (See page 32.) | |
the TV screen. |
|
| |
|
|
| |
Hard to listen to | Antennas are disconnected. | Reconnect the antennas correctly and securely. (See | |
broadcast because of |
| page 7.) | |
noise. |
|
| |
|
|
|
38