Technics SA-DX1050, SA-DX950 Customizing your receiver, Setting descriptions, Input Digital input

Page 12
CD: COAX
DVD: OPT2
TV: OPT1

FRONT

CENTER

FRONT

SMALL

LARGE

 

 

 

 

CENTER, SURROUND

SUB-WFR

SURROUND

NONE

SMALL

LARGE

 

 

 

 

SUB-WFR

NO

YES

FRONT

CENTER

1.0 m

10.0 m

 

SURROUND

 

 

 

 

 

100

150

200

 

 

 

OFF

STANDARD

MAX

 

 

 

CD

 

DVD

 

COAX

OPT1

OPT2

 

TV

 

 

 

 

 

 

OFF

ON

 

 

 

 

Customizing your receiver

Change the settings to suit your speakers and equipment and to suit the environment in which the unit is to be used. Before making any changes, read the following descriptions, note the factory settings and ranges, and refer to the instructions for the speakers and equipment.

The settings remain intact until they are changed, even after the power is turned off.

Setting descriptions

SIZE

Change to suit the speakers you have connected.

LARGE: For speakers that can reproduce a full sound range, particularly the bass range below 100 Hz.

SMALL: For speakers that cannot adequately reproduce the bass range. This setting is sufficient for most speakers if you are using a subwoofer.

NONE: For speakers you haven’t connected (center or surround).

The factory settings are: Front:LARGE Center and surround: SMALL

For the subwoofer, select YES if you have connected one (factory setting), or NO if you have not.

DISTANCE

Enter the distance of the speakers from the seating position so that the sound from all the speakers (except for the subwoofer) reaches you at the same time.

You can select distances between 1.0 and 10.0 m at 0.1 m

intervals.

 

 

The factory settings are:

Front and center:

3.0 m

 

Surround:

1.5 m

FILTER

This setting allows you to change the cut-off for bass output from the front speakers. If you set the front speakers to “SMALL”, the filter is set to 100 Hz. Raise the cut-off if the bass from the front speakers is unsatisfactory so that this bass is output through the subwoofer.

You can raise the cut-off from 100 Hz to either 150 Hz or 200 Hz.

DR COMP - Dynamic range compression

Change this setting to view software at low volume (such as late at night) and maintain audio clarity. This setting works with Dolby Digital software. It reduces the peak level in loud scenes without affecting the sound field.

OFF: The software is played with the original dynamic range (factory setting).

STANDARD: The level recommended by the producer of the software for household viewing.

MAX: The maximum allowable compression (recommended for night viewing).

D-INPUT - Digital input

Change these settings to suit the connections you have made to the three digital input terminals, COAX, OPT1, and OPT2 (\ page 7), so that the correct source is selected when you turn [INPUT SELECTOR] (\ page 18).

The factory settings are:

DIMMER

This setting allows you to dim the unit’s display (and turn off the MOS-FET light on SA-DX1050) for better viewing in a darkened room.

The factory setting is OFF (normal brightness).

12

RQT5802

Image 12
Contents AV Control Receiver Table of contents Supplied accessories Safety precautionsBefore use How to replace the fuse Before useEB area code model only Control reference guide Display sectionPS, RT, PTY, EON FIXED, PCM DIGITAL, % PRO LogicConnecting video equipment ConnectionsConnecting audio equipment Connecting digital equipmentChanging the digital input settings ConnectionsAntenna connections ConnectionsFM antenna AM loop antennaConnecting the AC mains lead and other information Placement of speakers Connecting speakersSpeaker connections Speaker impedance 6-16Ω Center speakerSurround speakers SubwooferSetting descriptions Customizing your receiverDR Comp Dynamic range compression Input Digital inputChange the settings a below Repeat steps 3 and 4 to complete the necessary SettingsChanging the settings Basic stepsFor front speakers with an impedance under 6 Ω Speakers A, BAdjusting speaker output level PreparationsStereo mode Surround modeChanging the recognition mode DSP sound modesOperations SFC modesEnjoying the sounds Press DVD 6CH Input Press BEnjoying the sounds Adjusting the tone and balance Using the VCR 2 terminalsUsing headphones Muting the volume Adjusting the subwoofer levelUsing the Tape Monitor Manual tuning Direct tuningRadio Press TUNER/BANDPreset tuning Press PresetPress Tuning 2 or FunctionsRDS broadcasts Only for Europe To display RDS informationPTY search EON tuning To cancel EON tuningPress BAND, EON PTY displaysMaking a recording Recording on a tape or MD deck Or VCRTimer function Setting the timersPress TIMER, -MODE, -TIME to select the desired timer mode ReferenceMaintenance Press -HELP, -RESETHelp function If the surfaces are dirtyTroubleshooting guide Common problemsDSP sound modes RadioSpecifications DIN 45 Memo Varoitus

SA-DX1050, SA-DX950 specifications

The Technics SA-DX950 and SA-DX1050 are two prominent models in the world of home audio receivers, designed to deliver exceptional performance and versatility for audiophiles and casual listeners alike. Both models reflect Technics' long-standing commitment to high-quality sound reproduction and innovative technology.

The SA-DX950 features advanced digital signal processing (DSP), which allows it to decode a variety of audio formats, enhancing the listening experience with exceptional clarity and detail. This model includes a built-in 5.1-channel amplifier, delivering robust power to drive a wide range of speakers, making it suitable for both music and home theater applications. With its THX certification, the SA-DX950 ensures that audio output meets rigorous standards set for high-fidelity surround sound, bringing cinema-like experiences into the home environment.

The SA-DX1050, while sharing many traits with the SA-DX950, is designed with even more advanced features. It boasts a higher power output and improved audio processing capabilities, assuring listeners a more immersive and dynamic soundstage. The model supports various surround sound formats, including Dolby Digital and DTS, which further enhances its ability to present engaging audio for movies, music, and games.

One of the standout characteristics of these models is the incorporation of Technics' proprietary digital amplifier technology. This technology minimizes distortion and maximizes efficiency, allowing for pure sound reproduction without the bulkiness typically associated with traditional amplifiers. Additionally, both receivers provide multiple inputs, enabling users to connect various devices such as CD players, DVD players, and gaming consoles seamlessly.

Another notable feature is the user-friendly interface, which simplifies navigation through the receiver's multitude of settings and options. The remote control further enhances this convenience, making it easy to adjust settings from a distance.

In conclusion, the Technics SA-DX950 and SA-DX1050 are exceptional audio receivers that embody cutting-edge technological advancements and superior sound quality. With their powerful amplification, robust surround sound capabilities, and user-friendly design, they are ideal choices for anyone looking to elevate their home audio experience. Whether for music, movies, or gaming, these receivers deliver an impressive and immersive sound that meets the highest expectations of audio enthusiasts.