Technics Troubleshooting Common Issues and F61 Error Code for CD Players

Page 27

Troubleshooting guide

Before requesting service, make the below checks. If you can’t fix the system as described below, or if something not listed here occurs, refer to the enclosed directory to locate an Authorized Service Center convenient to you or contact your dealer.

Reference pages are shown as black circled numbers y.

Common Problems

No sound.

Turn the volume up.

 

The speaker cords may be shorted. Turn the unit off, check and correct the connections and turn the

 

unit on. y

Sounds unfixed, reversed or

Check the speaker connections. y

come from one speaker only

 

 

 

Humming heard during play

An AC mains lead or fluorescent light is near the cables. Keep other appliances and leads away from

 

this unit’s cables.

 

If possible in your area, turn the AC mains lead’s plug or connector over to reverse the lead’s

 

polarity.

“ERROR” is displayed.

Incorrect operation performed. Read the instructions and try again.

 

 

“U70” is displayed

Connect the flat cables firmly. If “U70” remains on the display, contact the dealer.

“F61” is displayed.

There is a problem with the amplifier. Consult your dealer.

 

 

ECO mode on but display still

Turn DEMO off. !0

lights up in standby mode.

 

Listening to the radio

 

Noise is heard.

The stereo indicator flickers or doesn’t light.

Sound is distorted.

A beat sound is heard.

A low hum is heard during AM broadcasts.

The correct AM frequency can’t be tuned in.

Use an outdoor antenna. i

Turn the TV off or separate it from the unit.

Separate the antenna from other cables and leads.

Change the frequency step. Hold [FM/AM] or [AM] down for 10 seconds to change the step to 9 kHz.

The cassette deck

Poor quality sound.

Clean the heads. @6

 

Check the Dolby NR setting. !4

Recording is not possible.

If the erasure prevention tabs have been removed, cover the holes with adhesive tape. !9

 

 

The CD player

The display is wrong or play

The disc may be upside down. !6

won’t start.

Wipe the disc.

 

Replace the disc if it is scratched, warped, or nonstandard. !6

 

Condensation may have formed in the player due to a sudden change in temperature. Wait about an

 

hour for it to clear and try again.

 

 

During “One touch” editing (a Page 21)

“NO TAPE” is displayed.

Load a cassette. !4

 

 

“CHANGE TAPE” is displayed.

If the erasure prevention tabs have been removed, cover the holes with adhesive tape. !9

The remote control

The remote control doesn’t work.

Check the batteries are inserted correctly. t

 

Replace the batteries if they are worn.

 

 

All components are required to service the system. If service is ever necessary, bring the entire system.

Reference

27

RQT5296

Image 27
Contents SC-HD310 System SC-HD510 SC-HD310 RS-HDA710RAK-HDA26WH RAK-HDA25WH Table of contents Safety precautions How to replace the fuse Before useEB area code model only Use Remote controlInstallation BatteriesSpeaker Amplifier ConnectionsBasic connections for supplied accessories FM outdoor antenna Optional antenna connectionsConnections External unit connectionsTuner Front panel controlsCD player Cassette deckFront panel controls Remote controlTurning the Demo function off AmplifierClock Play REC Setting the timeSaving power in standby mode QPress /I to turn the unit on Press ModePress FM or AM to select the band Radio manual tuningPress Tune Mode to select Manual Adjust the volumePress the numbered buttons to select the channel Radio preset tuningHold down SET Press TunerCassette tapes Press TPS or TPS while the tape is stopped Press TPS Skip to selectCassette tapes Press OPEN/CLOSE to open the tray Press u to start play Adjust the volumeCDs Normal playPress Repeat before or during play Other modes of playSelect the track with the numbered buttons Press RandomProgram play Press sPress OPEN/CLOSE, insert Cassette with the tape facing Press REV Mode to select Reverse modeBefore recording Preparatory stepsRecording the radio Recording CDsNormal recording Linking One touch CD editing AI EditPress AI Edit Recording CDsPress /I to turn the unit off Using the timersPlay timer QPress CLOCK/TIMER, -DEMO to select PlayRecord timer QPress CLOCK/TIMER, -DEMO to select RECUsing the timers Press Sleep to select the time minutes Play and record timersSleep timer Using the timers togetherRecording an external source Using other equipmentUsing headphones not included Listening to an external sourceConvenient functions MaintenanceTroubleshooting guide Technical specifications DIN 45