CONSUMPTION DATA
| Temperature | Load | Water | Energy | Approx. Programme |
Programme | Selector |
|
|
| Duration |
|
|
|
|
| |
| (°C) | (kg) | (l) | (kWh) | (hours : minutes) |
Cotton | 95 | 5.0 | 63* | 1.80 | 2:05 |
|
|
|
|
|
|
Cotton | 60 | 5.0 | 55 | 1.20 | 2:05 |
|
|
|
|
|
|
Cotton | 40 | 5.0 | 55 | 0.55 | 2:05 |
|
|
|
|
|
|
Synthetic | 60 | 2.0 | 56 | 0.80 | 1:30 |
|
|
|
|
|
|
Synthetic | 40 | 2.0 | 56 | 0.40 | 1:30 |
|
|
|
|
|
|
Delicate | 40 | 1.5 | 60 | 0.55 | 0:45 |
|
|
|
|
|
|
Wool | 40 | 1.0 | 60 | 0.50 | 0:40 |
|
|
|
|
|
|
Silk | 30 | 1.0 | 60 | 0.30 | 0:50 |
|
|
|
|
|
|
Prewash cycle increases programme duration approximately 15 min. Consumption values were measured in normalized conditions in compliance with standard IEC/EN 60 456. Consumption data in the home may vary with respect to the values in the table in relation to the water supply pressure and temperature, the load and the type of wash.
The data on the “Energy Label” refer to the programme “Cotton 60°C”.
*To reduce the water temperature, some cold water is added at the end of the main wash cycle, before the pump drains the water out.
“Rinse Hold” button
•The laundry remains in the last rinse water without progressing to the final spin cycle to avoid creasing and prevent colours from fading.
•This option is particularly recommended for the “Synthetic”, “Delicate” and “Daily Mixed” programmes.
•This function is particularly useful if you want to postpone spinning to a later time, or if you want to drain only.
Note: the programme selector knob stops on 
.
Appliance in “Rinse Hold”:
•Press the “Rinse Hold” button again: the programme will terminate automatically with the selected spin cycle.
•If you do not wish to spin the clothes, press the “On/Off” button, turn the programme selector knob to the “Drain” programme and press the “On/Off” button again.
END OF WASH CYCLE
•The programme selector knob is in the Stop position.
1.Press the “On/Off” button to switch off the machine.
2.Cancel the options.
3.Turn the tap off.
4.Wait for the lid to unlock (about 1 minute).
5.Open the lid and the drum doors and unload the machine.
CHANGE THE PROGRAMME DURING THE WASH CYCLE
1.Switch off the machine by pressing the “On/Off” button.
2.Select the new programme.
3.Start programme by pressing the “On/Off” button again.
PAUSE/INTERRUPT A PROGRAMME
PREPARATION OF WASH CYCLE
1.Load the machine, close the drum doors and check that they are properly locked.
2.Add detergents and additives into the dispenser to no more then the “MAX” level mark, as follows:
• Programme with pre and main wash
• Main wash programme without prewash
• Fabric softeners and conditioners
• Chlorine bleach
• Stain remover agents
•
3.Turn the programme selector knob to the desired programme.
4.Turn the temperature selector knob to the desired temperature.
5.Turn the spin speed selector knob to the desired spin speed. If the spin speed “ 
” is selected, the final spin is cancelled, but not the intermediate spins. The programme ends with a drain cycle.
SELECT THE DESIRED OPTION
Selecting or deselecting an option can be done at any time during the programme. The option will be applied as long as the corresponding programme phase has not been executed yet.
“Rapid” button
•For fast, energy saving wash cycles.
•Ideally suited for small loads consisting of lightly soiled laundry.
“Half Load” button
•Can be used for small loads and lightly soiled laundry.
•Reduces the water consumption especially during the rinses.
“Intensive Rinse” button
•The amount of water is increased to ensure a more intensive rinse.
•This option is particularly suitable for areas with very soft water or washing linen laundry for people with skin allergies.
PROGRAMME START
Turn on the tap and press the “On/Off” button. The indicator light of the “On/Off” button lights up. Note: If there is a power interruption or if the appliance is disconnected during the cycle, the programme will run again from the point where it was interrupted.
If, for any reason, you wish to interrupt the programme for a certain time and continue it later:
1.Press the “On/Off” button.
2.After the desired pause, press again the “On/Off” button.
CANCEL PROGRAMME
1.Switch off the machine by pressing the “On/Off” button.
2.Set the programme selector to “Drain”.
3.Press the “On/Off” button again to start the “Drain” programme.