Smeg K400TL manual Programme Temperature Load Water Energy, Min, Terminate the Rinse Hold option

ENERGY AND WATER CONSUMPTION DATA

Programme	Temperature	Load	Water	Energy	Programme
					time
	(°C)	(kg)	(l)	(kWh)	(min)
Cotton	90	5.0	72	1.80	115
Cotton	60	5.0	72	1.20	115
Coloured	60	2.0	60	0.80	100
Coloured	40	2.0	60	0.40	100
Quick Wash + 1/2 Load	40	2.5	54	0.50	85
Synthetics + 1/2 Load	30	1.0	54	0.30	70
Delicate	40	1.5	70	0.65	55
Wool	40	1.0	70	0.55	45

Prewash cycle increases programme duration approximately 15 min. Consumption values were measured in normalized conditions in compliance with standard IEC/EN 60 456. Consumption data in the home may vary with respect to the values in the table in relation to the water supply pressure and temperature, the load and the type of wash. The data on the “Energy Label” refer to the programme “Cotton 60°C”.

Terminate the “Rinse Hold” option.

•Press the “Rinse Hold” button again; the programme will terminate automatically with the spin cycle corresponding to the previously selected wash programme.

•If you do not wish to spin the clothes, switch off the appliance by turning the spin speed knob to the Off position. The pilot light goes out. Turn the programme selector to the “Drain” position and switch on the appliance.

PROGRAMME START

Open the water inlet tap and press the “On/Off” button. The pilot lamp lights up.

DOOR LOCK

During the running programme, the door cannot be opened.

The door locks automatically in all programmes.

TO STOP, RESET A PROGRAMME BEFORE THE END

1.Press the “On/Off” button to switch off the appliance. The pilot lamp goes out

2.Set the programme selector on “Drain”.

3.Press the “On/Off” button to to start the “Drain” programme.

Only open the door when the programme selector is at “Stop” and the door is unlocked (after approximately 1 minute).

NOTES AND INDICATIONS FOR USE

•	After switching your washing machine on, it
	does not start immediately: it needs some
	seconds in order to lock the door, fill water and
	then drum starts turning.
•	Spinning has an interrupted start-up: the drum
	starts and stops running several times, to

PREPARATION OF WASH CYCLE

1.Close the drum flaps and check that they are properly locked.

2.Add detergents and additives into the dispenser to no more then the “MAX“ level mark, as follows:

• Programme with pre and main wash

• Main wash programme without prewash

• Fabric softeners and conditioners

• Chlorine bleach

• Stain remover agents

• Anti-scale agents (if necessary)

3.Turn the programme selector knob clockwise to the desired programme.

4.Turn the temperature knob to the required temperature.

PRESS ANY DESIRED OPTION BUTTON(S)

“No spin” button

•Especially for delicate garments to avoid wear and tear caused by the spin.

Note: with the “Cotton” and “Synthetics” programmes a short spin cycle is provided in any case, even if the exclusion has been selected, in order to optimize rinsing results.

“Half Load” button

•Reduces the water consumption in the “Cotton” and “Synthetics” programmes especially during the rinse.

•Especially suitable for lightly soiled or small loads (reduces the quantity of detergent).

•Not suitable for high temperature programmes.

“Rinse Hold” button

•The laundry remains in the last rinse water, without progressing to the spin cycle to avoid creasing and prevent colours from changing.

•This option is especially recommended for the “Synthetics” or “Delicate” programmes.

•This option is perfectly suitable if you wish to postpone the spin or you don't wish to spin the clothes.

Note: the programme selector stops on “”.

If the programme is stopped or if an electrical power failure occurs, the door unlocks automatically after about 1 minute.

PROGRAMME END

•The programme selector knob is at “STOP”, the pilot lamp lights.

1.Press the “On/Off” button . The pilot lamp goes out.

2.Cancel the options by pressing the appropriate buttons.

3.Turn the water supply tap off.

4.Wait for the door to unlock (about 1 minute).

5.Open the door and the drum flaps and unload the machine.

SELECTING A NEW PROGRAMME, SPIN SPEED, OPTIONS AFTER PROGRAMME START

1.Press the “On/Off” button. The pilot lamp goes out

2.Select the new programme, temperature and options.

3.Press the “On/Off” button to switch on the appliance. The pilot lamp lights up.

	improve spin efficiency and to better balance
	the laundry.
•	At the end of the spinning cycle the drum goes
	on reversing for some minutes: this helps you
	unloading the laundry.
•	Do not exceed in detergents dosage: excessive
	foam formation may prevent spinning.

5019 612 10059