Beko User's Manual WM 95135 LB WM 95145 LW Installation, Appropriate installation location

Page 9
WARNING: Do not remove the transportation locks before taking out the packaging reinforcement.

3Installation

Refer to the nearest Authorised Service Agent for installation of the product. To make the product ready for use, review the information in the user manual and make sure that the electricity, tap water supply and water drainage systems are appropriate before calling the Authorized Service Agent. If they are not, call a qualified technician and plumber to have any necessary arrangements carried out.

C Preparation of the location and electrical, tap water and waste water installations at the place of installation is under customer's responsibility.

B WARNING: Installation and electrical connections of the product must be carried out by the Authorized Service Agent. Manufacturer shall not be held liable for damages that may arise from procedures carried out by unauthorized persons.

A WARNING: Prior to installation, visually check if the product has any defects on it. If so, do not have it installed. Damaged products cause risks for your safety.

C Make sure that the water inlet and discharge hoses as well as the power cable are not folded, pinched or crushed while pushing the product into its place after installation or cleaning procedures.

3.1 Appropriate installation location

•Place the machine on a rigid floor. Do not place it on a long pile rug or similar surfaces.

•Total weight of the washing machine and the dryer -with full load- when they are placed on top of each other reaches to approx. 180 kilograms. Place the product on a solid and flat floor that has sufficient load carrying capacity!

•Do not place the product on the power cable.

•Do not install the product at places where temperature may fall below 0ºC.

•Place the product at least 1 cm away from the edges of other furniture.

3.2Removing packaging reinforcement

Tilt the machine backwards to remove the packaging reinforcement. Remove the packaging reinforcement by pulling the ribbon.

3.3Removing the transportation locks

A

A WARNING: Remove the transportation safety bolts before operating the washing machine! Otherwise, the product will be damaged.

1.Loosen all the bolts with a suitable spanner until they rotate freely (C).

2.Remove transportation safety bolts by turning them gently.

3.Attach the plastic covers supplied in the User Manual bag into the holes on the rear panel. (P)

Washing Machine /User’s Manual

9 / 40 EN

 

 

Page 8 Page 10
Image 9
Page 8 Page 10
Contents Washing Machine Important information or useful hints about usage Dear Customer Explanation of symbolsInstallation Important instructions for safety Environment4Maintenance and cleaning TroubleshootingGeneral safety Important instructions for safety and environmentUnplug the product when not in use Service life of your product is 10 yearsCompliance with Weee Directive Package informationDisposing of the waste product This appliance’s packaging material isYour washing machine Power cableOverview Top panel Loading door Control panelYour washing machine Package Contents Total current a Total power W 2200 Spin speed rpm max Your washing machine Technical specificationsStand-by mode power W Off-mode power W Main model code Single Water inlet / Double Water inlet AvailableAppropriate installation location InstallationRemoving packaging reinforcement Removing the transportation locksConnecting water supply InstallationConnecting to the drain Inlet11 / 40 EN Adjusting the feetInstallation Electrical connection Fitting a different plug12 / 40 EN 13 / 40 EN Preparation Sorting the laundry14 / 40 EN Initial use Preparation Preparing laundry for washingThings to be done for energy saving 15 / 40 ENUsing detergent and softener Preparation Correct load capacityLoading the laundry Preparation Adjusting detergent amountUse different detergents for coloured and white laundry 17 / 40 ENUsing bleaches Using starchDo not use softener and starch together in a washing cycle Do not use bleaching agent and detergent by mixing them19 / 40 EN Preparation Tips for efficient washingOperating the product Display symbolsControl panel On / Off buttonProgramme selection Operating the product Preparing the machineMain programmes Additional programmesSpecial programmes Operating the productSpin speed selection Temperature selection23 / 40 EN Use a lower spin speed for delicate laundries24 / 40 EN Programme and consumption tablePrewash Operating the product Auxiliary function selectionExtra Rinse 25 / 40 ENChanging the delayed start period Delayed startCancelling the Delayed Start function Time displayProgress of programme Operating the product Starting the programmeLoading door lock Changing the selections after programme has startedMachine is in Rinse Hold mode Cancelling the programmeChild Lock End of programme29 / 40 EN Quick User GuideCleaning the loading door and the drum Cleaning the detergent drawer30 / 40 EN MonthsCleaning the water intake filters Maintenance and cleaningCleaning the body and control panel Draining remaining water and cleaning the pump filterInstall the filter Pull the emergency draining hose out from its seat32 / 40 EN 33 / 40 EN TroubleshootingProgramme cannot be started or selected Machine does not fill with water34 / 40 EN TroubleshootingIt does not rinse well 35 / 40 ENDetergent residue in the detergent drawer 36 / 40 ENWater pressure is low. Check the water pressure Foam is overflowing from the detergent drawerLoading door may be open. Close the loading door On / Off button might not be pressed. Press On / Off button37 / 40 EN Machine does not start. Nothing appears on the display38 / 40 EN Complying Commission Delegated Regulation EU No 1061/201Washing Machines ServiceWashing Machines, Dishwashers and Electric Cookers Guarantee
Top Page Image Contents