Beko User's Manual WM 95135 LB WM 95145 LW Installation, Connecting water supply, Inlet

Page 10

Installation

CKeep the transportation safety bolts in a safe place to reuse when the washing machine needs to be moved again in the future.

CNever move the product without the transportation safety bolts properly fixed in place!

3.4 Connecting water supply

CThe water supply pressure required to run the product is between 1 to 10 bars (0.1 – 10 MPa). It is necessary to have 10 – 80 liters of water flowing from the fully open tap in one minute to have your machine run smoothly. Attach a pressure reducing valve if water pressure is higher.

CIf you are going to use the double water- inlet product as a single (cold) water-inlet unit, you must install the supplied stopper to the hot water valve before operating the product. (Applies for the products supplied with a blind stopper group.)

AWARNING: Models with a single water inlet should not be connected to the hot water tap. In such a case the laundry will get damaged or the product will switch to protection mode and will not operate.

AWARNING: Do not use old or used water inlet hoses on the new product. It may cause stains on your laundry.

1.Connect the special hoses supplied with the product to the water inlets on the product. Red hose (left) (max. 90 ºC) is for hot water inlet, blue hose (right) (max. 25 ºC) is for cold water

inlet.

AWARNING: Ensure that the cold and hot water connections are made correctly when installing the product. Otherwise, your laundry will come out hot at the end of the washing process and wear out.

2.Tighten all hose nuts by hand. Never use a tool when tightening the nuts.

3.Open the taps completely after making the hose connection to check for water leaks at the connection points. If any leaks occur, turn off the tap and remove the nut. Retighten the nut carefully after checking the seal. To prevent water leakages and damages caused by them, keep the taps closed when the machine is not in use.

3.5 Connecting to the drain

•The end of the drain hose must be directly connected to the wastewater drain or to the washbasin.

A WARNING: Your house will be flooded if the hose comes out of its housing during water discharge. Moreover, there is risk of scalding due to high washing temperatures! To prevent such situations and to ensure smooth water intake and discharge of the machine, fix the end of the discharge hose tightly so that it cannot come out.

10 / 40 EN

Washing Machine /User’s Manual

 

 

Page 9 Page 11
Image 10
Page 9 Page 11
Contents Washing Machine Dear Customer Explanation of symbols Important information or useful hints about usageMaintenance and cleaning Important instructions for safety Environment4Installation TroubleshootingUnplug the product when not in use Important instructions for safety and environmentGeneral safety Service life of your product is 10 yearsDisposing of the waste product Package informationCompliance with Weee Directive This appliance’s packaging material isOverview Power cableYour washing machine Top panel Loading door Control panel Your washing machine Package Contents Stand-by mode power W Off-mode power W Main model code Your washing machine Technical specificationsTotal current a Total power W 2200 Spin speed rpm max Single Water inlet / Double Water inlet AvailableRemoving packaging reinforcement InstallationAppropriate installation location Removing the transportation locksConnecting to the drain InstallationConnecting water supply InletAdjusting the feet 11 / 40 ENFitting a different plug Installation Electrical connection12 / 40 EN 13 / 40 EN Sorting the laundry Preparation14 / 40 EN Things to be done for energy saving Preparation Preparing laundry for washingInitial use 15 / 40 ENPreparation Correct load capacity Using detergent and softenerLoading the laundry Use different detergents for coloured and white laundry Adjusting detergent amountPreparation 17 / 40 ENDo not use softener and starch together in a washing cycle Using starchUsing bleaches Do not use bleaching agent and detergent by mixing themPreparation Tips for efficient washing 19 / 40 ENControl panel Display symbolsOperating the product On / Off buttonMain programmes Operating the product Preparing the machineProgramme selection Additional programmesOperating the product Special programmes23 / 40 EN Temperature selectionSpin speed selection Use a lower spin speed for delicate laundriesProgramme and consumption table 24 / 40 ENExtra Rinse Operating the product Auxiliary function selectionPrewash 25 / 40 ENCancelling the Delayed Start function Delayed startChanging the delayed start period Time displayLoading door lock Operating the product Starting the programmeProgress of programme Changing the selections after programme has startedChild Lock Cancelling the programmeMachine is in Rinse Hold mode End of programmeQuick User Guide 29 / 40 EN30 / 40 EN Cleaning the detergent drawerCleaning the loading door and the drum MonthsCleaning the body and control panel Maintenance and cleaningCleaning the water intake filters Draining remaining water and cleaning the pump filterPull the emergency draining hose out from its seat Install the filter32 / 40 EN Programme cannot be started or selected Troubleshooting33 / 40 EN Machine does not fill with waterTroubleshooting 34 / 40 EN35 / 40 EN It does not rinse wellWater pressure is low. Check the water pressure 36 / 40 ENDetergent residue in the detergent drawer Foam is overflowing from the detergent drawer37 / 40 EN On / Off button might not be pressed. Press On / Off buttonLoading door may be open. Close the loading door Machine does not start. Nothing appears on the displayComplying Commission Delegated Regulation EU No 1061/201 38 / 40 ENService Washing MachinesGuarantee Washing Machines, Dishwashers and Electric Cookers
Top Page Image Contents