John Lewis JLWM1604 instruction manual Unpacking, Positioning, Installation on a Suspended Floor

Page 7

Unpacking

All transit bolts and packing must be removed before using the appliance.

Keep all packaging away from children.

You are advised to keep all the transit bolts for re-use in case the machine is to be transported again.

After removing all the packaging, with assistance carefully lay machine on it’s back to remove the polystyrene base from the bottom.

Remove the power supply cable and the draining hose from the hose holders on the rear of the appliance.

HEC0008

HEC0001

With the spanner provided unscrew and remove the central rear bolt A.

Unscrew and remove the two large rear bolts B and the six smaller bolts C.

Fill the smaller upper hole and the two large ones with the corresponding plastic plug caps supplied in the bag containing the instruction booklet.

HEC0010

HEC0005

 

Connect the water inlet hose as described under the paragraph “Water inlet”.

Positioning

Install the machine on a flat hard floor.

Make sure that air circulation around the machine is not impeded by carpets, rugs etc. Check that the machine does not touch the wall or other kitchen units.

Never place cardboard, wood or similar materials under the machine to compensate for any unevenness in the floor.

If the floor is carpeted or covered with crumbly or soft material, insert a rigid support base under the feet to

A

HEC00022

 

 

C

 

 

B

HEC0003S

C

B

prevent noise, vibration or displacement. The base should protrude a few centimetres beyond the edges of the machine.

Warning

The machine should NOT be placed on deep pile carpeting.

Remove the bracket D, refit the six smaller bolts C and slide out the relevant plastic spacer E.

Installation on a Suspended Floor

D

HEC0011S

E

C

HEC0023 C

Suspended wooden floors are particularly susceptible to vibration. To help prevent vibration we recommend you place a waterproof wood panel, at least 15 mm thick under the appliance, secured to at least 2 floor boards with screws. If possible install the appliance in one of the corners of the room, where the floor is more stable.

Note

Open the porthole and remove the polystyrene block fitted with the adhesive tape.

Please ensure that when the appliance is installed it is easily accessible for the engineer in the event of a breakdown.

7

Image 7
Contents Jlwm Spin washing machine Child Safety InstallationUse Environmental Information Maintenance and Cleaning ServiceMaterials marked with the symbol are recyclable Ecological hintsContents Prewash Main wash Fabric softener Child safety featureDescription of the appliance Detergent dispenser drawerTechnical specifications InstallationUnpacking Installation on a Suspended FloorPositioning Appliance must be connected to a cold water supply PlumbingWater inlet Water drainageOnto a sink outlet spigot LevellingInterest of the environment Blue- Neutral Brown- Live «E» or by the earth symbol or coloured green and yellowElectrical connection Permanent connectionFollowing pieces of information are shown on the display Control panelProgramme selector dial DisplayDoor cannot be opened because the water must be drained Spin buttonTo empty out water there are 2 options Extra rinse button Child lockProgramme option buttons Easy Iron buttonStart/Pause button Delay start buttonSelecting the delayed start Cancelling the delayed startProgramme information Acoustic SignalCompartment marked Measure out the detergent Switch the machine onLoad the laundry Measure out the fabric softenerSelect the desired options Select the Delay startSelect the spin speed, No Spin, Rinse hold or Quiet option Select the Easy Iron optionLeave the door ajar in order to air the washing machine How to change an option or a programme during its cycleHow to interrupt a programme End of programmeBath robe Hints & tips on washing1000g = 1 kg SheetImportant Notes Wash care symbolsWater Only at a temperature of 40C or higherWashing programmes Programme Consumptions Fabrics Type of laundrySoak Off / ResetProgramme Consumptions DescriptionMaintenance and cleaning Screw the pump cover fully Close the pump door Cleaning the water inlet filterEmergency emptying out Remove any objects from the pump impeller by rotating itSomething not working Light has gone out Machine vibrates whenSpinning Door will not open22/07 132 972