Kenmore 11026852500 Installation Requirements, Parts supplied, Alternate Parts, You will need

Page 2

INSTALLATION REQUIREMENTS

Assemble the necessary tools and supplies before beginning the washer installation. The parts supplied are in the washer basket.

Tools needed for connecting the drain hose and water inlet hoses:

Pliers that open to 1%6 in. (3.95 era)

Flashlight (optional)

Parts supplied:

3

4

5

1.Drain hose

2.Silver, double-wire hose clamp (for the bottom of the drain hose)

3.Yellow, single-wire hose clamp (for the top of the drain hose)

4.Water inlet hoses (2)

5.Flat water inlet hose washers (4)

Tools needed for securing the drain hose and leveling the washer:

Adjustable or open end wrench %_ in. (14 ram)

Level

Wood block

Ruler or measuring tape

Parts supplied:

12

1.Shipping strap with fastener

2.Front leveling feet with nuts (2)

Alternate Parts

Parts listed are available from your local Sears store or Sears Service Center. For further information, call 1-800-4-MY-HOME ®

(1-800-469-4663).

If You Have:

 

You Will Need to Buy:

 

 

Laundry

tub or

Sump pump

 

system

(if not

already

standpipe

taller

available)

 

 

 

 

 

 

than 96 in. (2.4 m)

 

 

 

 

 

 

 

 

1 in. (2.5 cm)

 

2 in. (5 cm) diameter

to 1 in. (2.5 cm)

diameter

 

 

 

diameter

standpipe adapter, Part No.

standpipe

 

 

3363920

 

 

 

 

 

 

 

Overhead

sewer

Standard

20 gal. (76 L) 39 in. (99 cm) tall

 

 

 

 

drain tub or utility sink, sump pump and

 

 

 

 

connectors

(available

from

local

 

 

 

 

plumbing

suppliers)

 

 

 

Floor drain

 

 

Siphon break,

Part Number

285320;

 

 

 

 

additional drain hose, Part Number

 

 

 

 

3357090

and

connector

kit,

 

 

 

 

Part Number

285442

 

 

 

Water faucets

 

2 longer

water

fill hoses:

 

 

beyond

reach

of

6 ft (1.8 m) Part Number

76314,

fill hoses

 

 

10 ft (3.6 m) Part Number

350008

Drain hose

too

Drain hose,

Part No. 388423 and hose

short

 

 

 

kit, Part

No.

285442

 

 

 

Drain hose

that is

Hose kit, Part No. 285442

 

too long

 

 

 

 

 

 

 

 

 

 

 

Lint clogged

drain

Drain protector,

Part No.

367031

Selecting the proper location for your washer improves performance and minimizes noise and possible washer "walk."

Your washer can be installed in a basement, laundry room, closet, or recessed area. (See "Drain System.")

IMPORTANT: Do not install or store the washer where it will be

exposed to the weather.

Proper installation is your responsibility.

You will need:

A water heater set to deliver 120°F (49°C) water to the washer.

A grounded electrical outlet located within 4 ft (1.2 m) of where the power cord is attached to the back of the washer. (See "Electrical Requirements.")

Hot and cold water faucets located within 4 ft (1.2 m) of the hot and cold water fill valves, and water pressure of 5-100 psi (34.5-690 kPa). Washers with triple dispensers require 20-100 psi (138-690 kPa) for best performance.

A level floor with a maximum slope of 1 in. (2.5 cm) under

entire washer. Installing the washer on carpeting is not recommended.

A sturdy floor to support the washer weight (washer, water and load) of 315 Ibs (143 kgs).

2

Image 2
Contents Washer Safety Table of Contents/ndice /Table des matibresAlternate Parts Installation RequirementsParts supplied If You Have You Will Need to BuyFloor drain system view Recessed area or closet installationLaundry tub drain system view Standpipe drain system wall or floor view IFor a permanently connected washer Installation InstructionsFor a grounded, cord-connected washer For standpipe or laundry tub drain systems To prevent drain water from going back into the washerConnect the inlet hoses to the washer Connect the inlet hoses to the water faucetsClear the water lines Check for leaksInstall the front leveling feet Your Home