Kenmore 110 Tools needed for connecting the water inlet hoses, Tools needed for installation

Page 5

INSTALLATION

REQUIREMENTS

Assemble the necessary tools and supplies before beginning the washer installation. The parts supplied are in the washer drum.

Tools needed for connecting the water inlet hoses

Pliers (that open to 1°A6in. [39.5 mm])

Flashlight (optional)

Tools needed for installation

Open end wrench % in. (17 mm) and V2 in. (13 mm)

Level

Wood block (2" x 4")

Ruler or measuring tape

Parts supplied

C>

Beaded strap

A pedestal may be purchased separately for this washer. This pedestal will add about 13 in. (33 cm) to the height of your unit for a total vertical height of approximately 51 in. (130 cm).

Optional Pedestal

This pedestal (with storage drawer) is available in three colors:

White - Part Number 42842

Bisque - Part Number 42844

Graphite - Part Number 42846

To order, call your local Sears store. For further information, please call 1-800-4-MY-HOME® (1-800-469-4663).

Transport bolt hole plug (4)

Parts listed are available from your local Sears store or Sears Service Center. For further information, please call 1-800-4-MY- HOME ® (1-800-489-4863}.

Selecting the proper location for your washer improves performance and minimizes noise and possible washer "walk."

Your washer

can be installed under a custom

counter, or in a

(((((((((((((((((((((

basement, laundry room, closet, or recessed area. (See "Drain

 

System.")

 

 

 

 

Companion

appliance location

requirements

should also be

 

considered.

Proper installation

is your responsibility.

 

You will need

A water heater

set to

deliver

120°F (49°C) water to the

 

washer.

 

 

 

A grounded electrical

outlet

located within 5 ft (1.5 m) of

 

where the power cord is attached to the back of the washer.

 

(See "Electrical

Requirements.")

If You Have

Laundry tub or standpipe taller than 96 in. (2.4 m)

Overhead sewer

You Will Need to Buy

Sump pump system (if not already available)

Standard 20 gal. (76 L), 30 in. (76.2 cm) tall drain tub or utility sink and sump pump (available from local plumbing suppliers)

• Hot and cold water faucets

located within 4 ft (1.2 m) of the

hot and cold water fill valves, and water pressure of

20-100 psi (137.9-689.6 kPa).

• A level floor with a maximum slope of 1 in. (2.5 cm) under

entire washer. Installing the washer on carpeting is not

recommended.

 

• A sturdy and solid floor to

support the washer with a total

weight (water and load) of

400 Ibs (180 kg).

Do not operate your washer in temperatures below 32°F (0°C). Some water can remain in the washer and can cause damage in

Floor

drain

Siphon break, Part Number 285834;

 

 

additional drain hose Part Number

 

 

8318155; and connector kit, Part

 

 

Number 285835

 

Drain

hose too

Drain hose extension kit,

Part Number

short

 

285863

 

Water

faucets

2 longer water fill hoses:

 

beyond reach of

6 ft (1.8 m) Part Number

76314,

fill hoses

10 ft (3.0 m) Part Number

350008

low temperatures.

Image 5
Contents Toronto, Ontario, Canada M5B 2B8 Protection Agreements Table of ContentsKenmore Elite Washer Warranty Your safety and the safety of others are very important Washer SafetyTools needed for installation Tools needed for connecting the water inlet hosesParts supplied You will needRecessed area or closet installation Washer DimensionsCustom undercounter installation Grounding Nstructons Connect the inlet hoses to the water faucets Installation InstructionsTse she Automatic Temperature Control ATC Catalyst Cleaning Action with Direct InjectionSensor Smart TM Electronic Controls Smart DispensersFire Hazard Washer USEChoosing the Right Detergent LiouiBleach compartment To cancel a cycleTo change Options and Modifiers after the cycle has started Estimated Time RemainingHeavy Cycle Soil LevelDuty DelicateTemperature Suggested Fabrics Temperature GuidePrewash HOTLoading suggestions maximum size loads Heavy Work Clothes Laundry TipsLoad Type Prewash ExtendedWasher Care Washer makes noise or vibrates TroubleshootingWasher wontstart Load too wet Dispensers clogged or leakingResidue or lint on load Stains on loadPage Cuidado ConsejosSolucion Nomeros DE Servicio ContraportadaSensor Smart TM Registro del producto Servicio de Reparacibn de la GarantiaGarantia total de un afio para las piezas mec&nicas Venta para consulta futuraSeguridad DE LA Lavadora Herramientas necesarias para la instalacibn Necesitara adquirirPiezas proporcionadas 4663Usted necesitara Dimensiones de la lavadoraInstalacibn personalizada debajo del mostrador Instalacibn en zona empotrada o en el clbsetSistema de desagiJe por el piso vista Sistema de desagie por el lavadero vistaInstrucciones Para LA Conexion a Tierra Instrucciones DE InstalacionPage Beneficios