KD-G116/KD-G115
Installation/Connection Manual
°“√µ‘¥µ—Èß/§ŸË¡◊Õ°“√µ‘¥µ—Èß
[U/UH]
ENGLISH
This receiver is designed to operate on 12 V DC, NEGATIVE ground electrical systems. If your vehicle does not have this system, a voltage inverter is required, which can be purchased at JVC car audio dealers.
1004DTSMDTJEIN EN, TH
‰∑¬
Parts list for installation and connection
The following parts are provided for this receiver. After checking them, please set them correctly.
A / B
Hard case/Control panel
FG
Washer (ø5) | Lock nut (M5) |
πÕµ≈ÁÕ§ M5( ) |
√“¬°“√ Ë«πª√–°Õ∫”À√—∫µ‘¥µ—Èß·≈–‡™◊ËÕ¡µËÕ°—π
C | D | E |
Sleeve | Trim plate | Power cord |
ª≈Õ°ÀÿÈ¡ | ||
H | I | J |
Mounting bolt (M5 x 20 mm) | Rubber cushion | Handles |
≈—°µ‘¥M5( x 20 ¡‘≈≈‘‡¡µ√) |
INSTALLATION |
|
The following illustration shows a typical installation. If you have any questions or require information regarding installation kits, consult your JVC car audio dealer or a company supplying kits.
•If you are not sure how to install this receiver correctly, have it installed by a qualified technician.
•
Do the required electrical connections.
µËÕ“¬‰øµ“¡∑’Ë°”À𥉫È∑—ÈßÀ¡¥
*1 When you stand the receiver, be careful not to damage the fuse on the rear.
*1
Removing the receiver |
|
Before removing the receiver, release the rear section. |
Bend the appropriate tabs to hold the sleeve firmly in place.
ßÕ·ºËπ‡æ◊ËÕ¬÷¥ª≈Õ°„ÀȵËÕ°—π‡¢È“∑’Ë
Insert the two handles, then pull them as illustrated so that the receiver can be removed.
„
When using the optional stay /
Fire wall | Stay (option) |
| |
Dashboard |
|
Screw (option) | |
|
°√Ÿ (‡≈◊Õ°‰¥È)
Install the receiver at an angle of less than 30˚.
µ‘¥µ—Èß™ÿ¥Õ∫∑’Ë¡ÿ¡µË”°«Ë“–ª√ 30 Õß»“
When installing the receiver without using the sleeve /
In a Toyota for example, first remove the car radio and install the receiver in its place.
Flat type screws |
| * Not included for this receiver. | |
(M5 x 8 mm)* |
| * | |
Bracket* | |||
| |||
(M5 x 8 ¡‘≈≈‘‡¡µ√)* | Flat type screws | ||
|
| (M5 x 8 mm)* | |
| |||
Bracket* | (M5 x 8 ¡‘≈≈‘‡¡µ√)* | ||
|
|
Note : When installing the receiver on the mounting bracket, make sure to use the 8
À¡“¬‡Àµ :
TROUBLESHOOTING
•The fuse blows.
* Are the red and black leads connected correctly?
•Power cannot be turned on. * Is the yellow lead connected?
•No sound from the speakers.
* Is the speaker output lead
•Sound is distorted.
*Is the speaker output lead grounded?
*Are the
•Noise interfere with sounds.
* Is the rear ground terminal connected to the carʼs chassis using shorter and thicker cords?
•Receiver becomes hot.
*Is the speaker output lead grounded?
*Are the
•This receiver does not work at all. * Have you reset your receiver?
°“√µ√«® Õ∫ª—≠À“¢—¥¢ÈÕß
• ø‘« Ï¢“¥
* ¡’°“√‡™◊ËÕ¡
• ‰¡Ë “¡“√∂‡ª‘¥‡§√◊ËÕ߉¥È
* ¡’°“√‡™◊ËÕ¡
• ‰¡Ë¡’‡ ’¬ßÕÕ°®“°≈”‚æß
*
• ‡ ’¬ß‡æ’Ȭπ
*
*
• ‡ ’¬ß√∫°«π
* ¡’°“√„™È “¬
•
*
*
•
1 *