Ariston CD12TUK manual Trouble shooting

Page 10

Z

Fig. 1

Fig. 2

Trouble shooting

Removing limescale

Water contains increasing amounts of limescale because of pollution. If you live in a hard water area in addition to using water-softener in each wash, it is a good idea to put the machine through a cycle without laundry or detergent, just using limescale remover.

If the machine does not seem to be working properly before calling the service engineer there are a number of things you can check. Perhaps you have forgotten to push in a button or you are not using the machine properly.

Machine won't start

Make sure:

the appliance is plugged to the mains socket; you have electricity in your home, the door is firmly shut, the ON/OFF button I is on I, the programming cycle knob, in washer- dryers which have one, is on O, the programme is properly set and the mains water tap is open.

Machine won't fill

Make sure:

the water tap is open and connected correctly to the hose; the water mains has not been cut off and that water pressure is sufficient; also check the hose for kinks.

Water is pumping in and out all the time

Make sure:

there are no kinks in the drain pipe and that it is at least at a height greater than 60 cm; the pipe mouth is not below water level and that the wall drain has no air outlet. If the problems continue even after you have checked these points, shut the water tap and turn off your machine.

Problems with pumping out water or spinning

Make sure:

the programme selected has a draining cycle; the non creasing "hydropstop" button, on washer-dryers which have one, has not been pressed accidentally; the drainage pump is not jammed; the drain pipe is bent; the drainage piping is plugged; any drainage pipe extensions are properly connected and do not prevent water flow.

The washer-dryer is not drying

Make sure:

the plug is inserted properly into the socket; there is electricity in the house; the washer-dryer door is closed; the ON-OFF button I is on the I setting; the programming cycle knob, in

washer-dryers which have one, is on the O setting; the program knob A is on the setting; the dryer knob C is on the O setting.

Lots of vibration during the spin

Make sure:

the internal oscillating unit was released correctly at the time of installation (see installation instructions); the washer is levelled correctly or too tightly fitted between furniture units and the wall.

Your washer is leaking.

Make sure:

the ring nut of the supply pipe is firmly tightened; the detergent dispenser is not plugged and the drainage pipe is firmly fixed.

Excessive formation of suds.

Make sure:

the type of detergent you have used - is it suitable for an automati washer - have you used too much detergent?

The washer-dryer is not drying efficiently.

Make sure:

the end of the drain hose is not immersed in water; the drain pump is not blocked (see "General maintenance"); the advice on maximum loads and drying times have been followed; the drying time selected is at least 20 minutes; the water tap is turned on.

If despite all this your washer-dryer is still not running properly, call your local Authorized Service Centre providing the following information:

-fault

-model code (Mod. ....) and serial number (S/N ....)

indicated on the plate located on the bottom part of the machine.

Never use the services of an unauthorised servicing technician and insist on the use of original spare parts.

9

GB

Image 10
Contents Ariston BUILT-IN Washer Dryer Saves while it washes Safety, a good habit to get intoMargherita Controlled consumptionOverview Using your washer-dryer At the end of the wash cycle Starting up your washer-dryerSelecting the programme Drying onlyAt the end of the drying cycle Now select the programmeWashing and drying Selecting the programmes MAXWashing tips General maintenance Energy saving hintsTrouble shooting Transit packing InstallationConnecting the drain pipe LevellingElectrical connection figure Hinge Supports Hinges Door Mounting Accessories FigMounting the Parts onto the Face of the Machine Magnet Rubber plug Magnet plateMounding the Parts onto the Wooden Panel Door Technical characteristicsUsing the Drilling Template Mounting the Panel into the machine