Perreaux SM6 MKII owner manual Maximising System Potential

Page 21

8Maximising System Potential

Interconnects

and Speaker

Cables

Bi-amping

Balanced Interconnects

An often-ignored area in high fidelity systems is the cabling connecting the various components. Interconnect leads should be high quality cable with substantial terminations. Gold plate is inherently resistant to corrosion, and an excellent conductor. The presence of corrosion induces distortion and poor conductivity will seriously interfere with sound quality. Terminations must plug snugly into sockets to maintain maximum conductivity and to avoid annoying earthing problems.

Speaker cabling is equally critical. Use only solidly constructed cable of high purity copper or silver content. Again, gold plated terminations are recommended, of the spade or banana plug type. Use cables of equal length and as short as possible to maintain uniform electrical resistance at the lowest possible level. If your amplifier is closer to one of your speakers than the other, avoid coiling the longer lead as this can create inductance, with the potential of reduced high frequency performance. Keep all connections clean, firm and tight. The traditional adage that a chain is only as strong as its weakest link most certainly applies to audio systems.

Bi-amping uses two similarly powered amplifiers, with exactly the same input sensitivity so that, when the same input signal is provided to each of them, the output level will be exactly the same. This can often be done with one power amplifier connected to the tweeters and another to the woofers, as it spreads the power requirement between the two amplifiers. Bi-amping can achieve greater control, dynamics and resolution than if you try to run everything from a single stereo amplifier.

The use of the balanced signal inputs and outputs can have the effect of cleaning up hums, buzzes, radio frequency interference (RFI) and general extraneous rubbish that can enter an audio system. A balanced signal input system operates on the principle of differential amplification. The positive and negative inputs are contrasted against one another and the difference between them is amplified. Noise entering the system is imposed equally on the positive and negative signals and therefore will not be amplified, as no differential voltage exists.

The term used to describe the quality of the effect is called Common Mode Rejection Ratio (CMRR). CMRR is an equipment and system specification, which describes how well unwanted common mode signals are counteracted when used in conjunction with balanced connections. CMRR action prevents the egress and build up of extraneous hum; buzzes and RFI when analogue signals are conveyed down cables and between equipment powered from different locations and is widely used in professional audio applications.

21

Page 20 Page 22
Image 21
Page 20 Page 22
Contents Prisma SM6 MkII Page Introducing the Perreaux SM6 MkII Preamplifier Ii Important Safety Instructions Iii Table of ContentsUnpacking and Placement Instant Install Start your source material playing Input a Input B Input C Input D HT Loop Input E Input F Front Panel FunctionsPage Rear Panel Functions Unbalanced Source Inputs Remote Trigger Outputs Plug must follow the specifications as per the diagram below Remote Control Functions Depressing this button increases the volume Scroll Source Up Special Design Philosophies Minimalism in a Wider Context Special Design Features Maximising System Potential Watts is twice as loud as 10 Watts, not ten times as loud Care and Maintenance Obtaining Service Warranty InformationRegistration Form Extended WarrantyFaultfinding Your System Identifying Isolating Problems Loudspeakers Preamplifier Amplifier Faultfinding Flowchart 8VRMS 13SpecificationsAudio Inputs Gain Resolution 5dB Input Sensitivity 200mV Physical Dimensions Contact Details Installation Notes

SM6 MKII specifications

The Perreaux SM6 MKII is an impressive amplifier that encapsulates the essence of high-fidelity audio performance, making it a remarkable choice for discerning audiophiles. Renowned for its robust build quality and sophisticated design, the SM6 MKII promises to deliver an immersive listening experience while showcasing the brand’s commitment to craftsmanship and innovation.

At the heart of the SM6 MKII is a high-power solid-state amplifier circuit that ensures dynamic and accurate sound reproduction. With a power output of 100 watts per channel into 8 ohms, the amplifier can easily drive a wide range of loudspeakers. It is designed to handle the most demanding musical passages without distortion, making it suitable for both loud and nuanced listening environments.

One of the standout features of the SM6 MKII is its dual-mono design, which helps to eliminate crosstalk between the left and right channels. This design philosophy not only enhances stereo imaging but also provides a more immersive soundstage. The amp utilizes a high-performance toroidal transformer, known for its efficiency and minimal electromagnetic interference, further enhancing the clarity of the audio signal.

The SM6 MKII integrates advanced technologies, such as the unique feedback topology that helps minimize distortion and improve signal integrity. This technology ensures that the amplifier remains stable under varying load conditions, providing consistent performance regardless of speaker impedance or volume levels. Additionally, the high-current output stage significantly contributes to its dynamic capabilities, allowing for impressive transient response.

Another characteristic of the SM6 MKII is its user-friendly interface. The amplifier features intuitive knobs and switches that enable easy adjustment of volume, balance, and input selection. The robust chassis construction not only contributes to its aesthetic appeal but also serves to reduce vibration and external interference, ensuring that the audio integrity is preserved.

Overall, the Perreaux SM6 MKII stands out as an excellent investment for those who prioritize audio fidelity and performance. With its powerful output, sophisticated design, and innovative technologies, it is well-equipped to deliver a captivating listening experience that meets the demands of even the most discerning listeners. Whether you're enjoying music in a casual setting or critically listening for nuances, the SM6 MKII provides a sound experience that is both engaging and lifelike.
Top Page Image Contents