Perreaux SM6 MKII owner manual Unpacking and Placement

Page 6

1 Unpacking and Placement

Unpacking Procedure

Note:

Note:

Box Contents

Placing Your SM6

The SM6 is packaged for maximum protection. Please carefully read the instructions below before proceeding to unpack the unit. Be extremely careful.

￿Inspect both ends of the cardboard box and open at the end without the central staple by slitting the reinforced tape at either side.

￿Fold back the flaps and tip the package on end and the inner box will slide out.

￿Lay the inner box down flat and upright, open it conventionally by separating the top tray from the bottom.

￿The product can now be removed from the bottom packaging. This will be easier if you have someone to help you by holding the base of the box.

￿Alternately, the bottom tray and preamplifier could be tipped upside down and the bottom packaging removed. If opened in this manner, please ensure that you turn the contents over again.

Be very careful to secure the unit if you are planning to flip the package upside down.

￿Remove the two grey foam protectors off either side of the unit, leaving the black material covering.

￿Pull back the material and remove the protective membrane from the front panel.

The preamplifier is now unpacked and ready for further installation.

Please retain all packaging material for future transport.

1 x SM6 MkII Preamplifier

1 x Screwdriver

1 x SM6 MkII Product manual

2 x Remote trigger leads

1 x Perreaux remote control

1 x Detachable AC power cord

2 x AAA batteries

3 x Performance analysis charts

The SM6 should generally be placed close to your amplifier, keeping the interconnect cabling short. Position all the separate components of your system close enough to your SM6 to avoid having to stretch or extend any of the interconnect cables.

As a “rule of thumb”, allow 80-100mm (3-4 inches) around all sides of the product and mount the SM6 on a flat surface, ensuring that the unit has adequate access to free flowing air.

Do not place auxiliary equipment directly on top of the SM6. Do not place the SM6 directly atop a power amplifier.

Please do not cover the product with a cloth or similar.

6

Page 5 Page 7
Image 6
Page 5 Page 7
Contents Prisma SM6 MkII Page Introducing the Perreaux SM6 MkII Preamplifier Ii Important Safety Instructions Table of Contents IiiUnpacking and Placement Instant Install Start your source material playing Front Panel Functions Input a Input B Input C Input D HT Loop Input E Input FPage Rear Panel Functions Unbalanced Source Inputs Remote Trigger Outputs Plug must follow the specifications as per the diagram below Remote Control Functions Depressing this button increases the volume Scroll Source Up Special Design Philosophies Minimalism in a Wider Context Special Design Features Maximising System Potential Watts is twice as loud as 10 Watts, not ten times as loud Care and Maintenance Warranty Information Obtaining ServiceExtended Warranty Registration FormFaultfinding Your System Identifying Isolating Problems Loudspeakers Preamplifier Amplifier Faultfinding Flowchart 13Specifications 8VRMSAudio Inputs Gain Resolution 5dB Input Sensitivity 200mV Physical Dimensions Contact Details Installation Notes

SM6 MKII specifications

The Perreaux SM6 MKII is an impressive amplifier that encapsulates the essence of high-fidelity audio performance, making it a remarkable choice for discerning audiophiles. Renowned for its robust build quality and sophisticated design, the SM6 MKII promises to deliver an immersive listening experience while showcasing the brand’s commitment to craftsmanship and innovation.

At the heart of the SM6 MKII is a high-power solid-state amplifier circuit that ensures dynamic and accurate sound reproduction. With a power output of 100 watts per channel into 8 ohms, the amplifier can easily drive a wide range of loudspeakers. It is designed to handle the most demanding musical passages without distortion, making it suitable for both loud and nuanced listening environments.

One of the standout features of the SM6 MKII is its dual-mono design, which helps to eliminate crosstalk between the left and right channels. This design philosophy not only enhances stereo imaging but also provides a more immersive soundstage. The amp utilizes a high-performance toroidal transformer, known for its efficiency and minimal electromagnetic interference, further enhancing the clarity of the audio signal.

The SM6 MKII integrates advanced technologies, such as the unique feedback topology that helps minimize distortion and improve signal integrity. This technology ensures that the amplifier remains stable under varying load conditions, providing consistent performance regardless of speaker impedance or volume levels. Additionally, the high-current output stage significantly contributes to its dynamic capabilities, allowing for impressive transient response.

Another characteristic of the SM6 MKII is its user-friendly interface. The amplifier features intuitive knobs and switches that enable easy adjustment of volume, balance, and input selection. The robust chassis construction not only contributes to its aesthetic appeal but also serves to reduce vibration and external interference, ensuring that the audio integrity is preserved.

Overall, the Perreaux SM6 MKII stands out as an excellent investment for those who prioritize audio fidelity and performance. With its powerful output, sophisticated design, and innovative technologies, it is well-equipped to deliver a captivating listening experience that meets the demands of even the most discerning listeners. Whether you're enjoying music in a casual setting or critically listening for nuances, the SM6 MKII provides a sound experience that is both engaging and lifelike.
Top Page Image Contents