Perreaux SM6 MKII owner manual Rear Panel Functions

Page 11

4

Rear Panel Functions

Caution!

Note:

Note:

Observe precautions regarding volume control settings. Please make all changes at minimum volume setting. Only increase the volume after the connections have been made.

Balanced Inputs

Accepts a signal from a source component with balanced outputs via high quality XLR connectors. The use of good quality balanced line cable into the balanced input cause the input signal to be relatively immune to noise and external effects caused by the use of long interconnect cables, helps reduce hum loop noise and aids in the cancellation of distortion products.

The pin assignments of the balanced XLR input connectors are as follows:

Pin 1: Signal ground

Pin 2: Signal + (non-inverting)

Pin 3: Signal – (inverting)

Shield ground: Chassis ground

Please refer to the operating manuals of your balanced output line level source to verify that the pin assignments of the output connectors correspond to the SM6 balanced inputs. In the event that they are not compatible, the interconnecting cable will need to be altered to suit.

Balanced Input Switch

This switch selects which input to use for source input A. Set to ON if using the balanced (XLR) inputs and OFF if using the unbalanced (RCA) inputs.

Do not connect source equipment to both the balanced and unbalanced inputs at any one time.

11

Page 10 Page 12
Image 11
Page 10 Page 12
Contents Prisma SM6 MkII Page Introducing the Perreaux SM6 MkII Preamplifier Ii Important Safety Instructions Iii Table of ContentsUnpacking and Placement Instant Install Start your source material playing Input a Input B Input C Input D HT Loop Input E Input F Front Panel FunctionsPage Rear Panel Functions Unbalanced Source Inputs Remote Trigger Outputs Plug must follow the specifications as per the diagram below Remote Control Functions Depressing this button increases the volume Scroll Source Up Special Design Philosophies Minimalism in a Wider Context Special Design Features Maximising System Potential Watts is twice as loud as 10 Watts, not ten times as loud Care and Maintenance Obtaining Service Warranty InformationRegistration Form Extended WarrantyFaultfinding Your System Identifying Isolating Problems Loudspeakers Preamplifier Amplifier Faultfinding Flowchart 8VRMS 13SpecificationsAudio Inputs Gain Resolution 5dB Input Sensitivity 200mV Physical Dimensions Contact Details Installation Notes

SM6 MKII specifications

The Perreaux SM6 MKII is an impressive amplifier that encapsulates the essence of high-fidelity audio performance, making it a remarkable choice for discerning audiophiles. Renowned for its robust build quality and sophisticated design, the SM6 MKII promises to deliver an immersive listening experience while showcasing the brand’s commitment to craftsmanship and innovation.

At the heart of the SM6 MKII is a high-power solid-state amplifier circuit that ensures dynamic and accurate sound reproduction. With a power output of 100 watts per channel into 8 ohms, the amplifier can easily drive a wide range of loudspeakers. It is designed to handle the most demanding musical passages without distortion, making it suitable for both loud and nuanced listening environments.

One of the standout features of the SM6 MKII is its dual-mono design, which helps to eliminate crosstalk between the left and right channels. This design philosophy not only enhances stereo imaging but also provides a more immersive soundstage. The amp utilizes a high-performance toroidal transformer, known for its efficiency and minimal electromagnetic interference, further enhancing the clarity of the audio signal.

The SM6 MKII integrates advanced technologies, such as the unique feedback topology that helps minimize distortion and improve signal integrity. This technology ensures that the amplifier remains stable under varying load conditions, providing consistent performance regardless of speaker impedance or volume levels. Additionally, the high-current output stage significantly contributes to its dynamic capabilities, allowing for impressive transient response.

Another characteristic of the SM6 MKII is its user-friendly interface. The amplifier features intuitive knobs and switches that enable easy adjustment of volume, balance, and input selection. The robust chassis construction not only contributes to its aesthetic appeal but also serves to reduce vibration and external interference, ensuring that the audio integrity is preserved.

Overall, the Perreaux SM6 MKII stands out as an excellent investment for those who prioritize audio fidelity and performance. With its powerful output, sophisticated design, and innovative technologies, it is well-equipped to deliver a captivating listening experience that meets the demands of even the most discerning listeners. Whether you're enjoying music in a casual setting or critically listening for nuances, the SM6 MKII provides a sound experience that is both engaging and lifelike.
Top Page Image Contents