Maytag MDG30PCC installation manual 75,&$/659,&63&,,&$7,2163555

Page 22

2.Electrical Service Specifications

*$6

(/(&75,&$/￿6(59,&(￿63(&,),&$7,216￿￿3(5￿'5<(5￿

127(6￿￿￿$￿￿￿￿:KHQ￿IXVHV￿DUH￿XVHG￿WKH\￿PXVW￿EH￿GXDO￿HOHPHQW￿￿WLPH￿GHOD\￿￿FXUUHQW￿OLPLWLQJ￿

￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿FODVV￿5.￿￿RU￿5.￿￿21/<￿￿￿&DOFXODWH￿GHWHUPLQH￿FRUUHFW￿IXVH￿YDOXH￿￿E\￿DSSO\LQJ

￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿HLWKHU￿ORFDO￿DQG￿RU￿1DWLRQDO￿(OFWULFDO￿&RGHV￿WR￿OLVWHG￿DSSOLDQFH￿DPS￿GUDZ￿GDWD￿

%￿ &LUFXLW￿EUHDNHUV￿DUH￿WKHUPDO￿PDJQHWLF￿￿LQGXVWULDO￿￿PRWRU￿FXUYH￿W\SH￿21/<￿￿￿)RU

RWKHUV￿￿FDOFXODWH￿YHULI\￿FRUUHFW￿EUHDNHU￿VL]H￿DFFRUGLQJ￿WR￿DSSOLDQFH￿DPS￿GUDZ￿UDWLQJ DQG￿W\SH￿RI￿EUHDNHU￿XVHG￿

6(59,&(

 

:,5(

$3352;￿

)86,1*

&,5&8,7

3+$6(

$03￿'5$:

'XDO￿(OHPHQW

92/7$*(

6(59,&(

%5($.(5

 

 

 

￿￿￿+]

￿￿￿+]

7LPH￿'HOD\

 

 

 

 

 

 

￿￿￿

￿¡

￿

￿￿￿

²

￿￿

￿￿

 

 

 

 

 

 

 

1/15/04

IMPORTANT: Figures shown are for non-reversing models only. For reversing models contact the factory.

3.Grounding

A ground (earth) connection must be provided and installed in accordance with state and local codes. In the absence of these codes, grounding must conform to applicable requirements of the National Electrical Code ANSI/NFPA NO. 70-LATEST EDITION, or in Canada, the installation must conform to applicable Canada Standards: Canadian Electrical Codes Parts 1 & 2 CSA C22.1-1990 or LATEST EDITION. The ground connection may be to a proven earth ground at the location service panel.

For added personal safety, when possible, it is suggested that a separate ground wire (no. 18 minimum) be connected from the ground connection of the dryer to a grounded cold water pipe. DO NOT ground to a gas pipe or hot water pipe. The grounded cold water pipe must have metal-to-metal connection ALL the way to the electrical ground. If there are any nonmetallic interruptions, such as, a meter, pump, plastic, rubber, or other insulating connectors, they must be jumped out with no. 4 copper wire and securely clamped to bare metal at both ends.

IMPORTANT: For personal safety and proper operation, the dryer must be grounded.

Provisions are made for ground connection in each dryer at the electrical service connection area.

4.Electrical Connections

A wiring diagram is located inside the control box for connection data.

If local codes permit, power to the dryer can be made by the use of a flexible U.L. listed power cord/pigtail (wire size must conform to rating of dryer), or the dryer can be hard wired directly to the service breaker panel. In both cases, a strain relief must be installed where the wiring enters the dryer.

IMPORTANT: A separate protected circuit must be provided to each dryer.

18

Image 22
Contents MDG30PCC Retain This Manual In a Safe Place For Future Reference Foryour Safety Page Table of Contents Section Procedure for Functional Check of Replacement Safety Precautions SectionPage Specifications FXPSpecifications GAS only Installation Procedures Unpacking and Setting UPLocation Requirements Dryer Enclosure Requirements Fresh AIR Supply Requirements Exhaust Requirements Single Dryer Venting Vertical Venting Multiple Dryer Common Venting Illus. D Importantventingreminders Electrical Information Electrical Requirements75,&$/659,&63&,,&$7,2163555 Odfn 3RVLWLYH KLWHRU5HG Uhhq UrxqgGAS Information 732*$6 This Pipe Size Requirement Page Preparation for Operation and START-UP Preoperational Tests Preoperational Instructions Coin Models Basket Tumbler CoatingShutdown Instructions Service SERVICE/PARTS InformationParts Returning Warranty Cards Warranty InformationWarranty Cleaning Routine MaintenanceSuggested Cleaning Schedule Adjustments LubricationSectionvii Datalabel InformationSerial Number Procedure for Functional Check Replacement Components SectionviiiPage Phase Manual Reset Burner HI-LIMIT InstructionsDual Timer 15/04