Installation Instructions

Electrical Requirements

■If codes permit and a separate earth wire is used, it is recommended that a qualified electrician determine that the earth path is adequate.

■If the supply cord is damaged, it must be replaced by the manufacturer, its service agent, or a qualified person to avoid a hazard.

■Do not earth to a gas pipe.

■Check with a qualified electrician if you are not sure the washer is properly earthed.

■Do not have a fuse in the neutral or earth circuit.

■A 220-240V, 50 Hz., fused electrical supply is required. A time-delay 10-16A fuse or circuit breaker is recommended.

■This washer is equipped with a power supply cord having an earthed plug.

■To minimize possible shock hazard, the cord must be plugged into an earthed socket outlet, earthed in accordance with local codes and ordinances. If a mating outlet is not available, it is the personal responsibility and obligation of the customer to have the properly earthed outlet installed by a qualified electrician.

EARTHING INSTRUCTIONS

This washer must be earthed. In the event of a malfunction or breakdown, earthing will reduce the risk of electric shock by providing a path of least resistance for electric current. This washer is equipped with a cord having an equipment-earthing conductor and an earthing plug. The plug must be plugged into an appropriate outlet that is properly installed and earthed in accordance with all local codes and ordinances.

WARNING: Improper connection of the equipment- earthing conductor can result in a risk of electric shock. Check with a qualified electrician or serviceman if you are in doubt as to whether the appliance is properly earthed.

Do not modify the plug provided with the appliance – if it will not fit the outlet, have a proper outlet installed by a qualified electrician.

Remove Transport System

WARNING

Excessive Weight Hazard

Use two or more people to move and install washer. Failure to do so can result in back or other injury.

IMPORTANT: Position the washer so that the rear of the washer is within approximately 900 mm (3 ft.) of its final location.

There are 4 shipping bolts in the rear panel of the washer that support the suspension system during transportation. These bolts also retain the power cord inside the washer until the bolts are removed.

2.Using a 1/2" wrench, loosen each of the bolts.

3.Once the bolt is loose, move it to the center of the hole and completely pull out the bolt, including the plastic spacer covering the bolt.

4.Once all 4 bolts are removed, discard the bolts and spacers. Then push the power cord plug into the opening on the right side of the rear panel and pull the power cord through the opening on the left side of the rear panel and close holes with the attached cap. Do not pull plug end of power cord through the right side hole.

5.Close the bolt holes with the 4 transport bolt hole plugs.

NOTE: If the washer is to be transported at a later date, call your product distributor or installer. To avoid suspension and structural damage, your washer must be properly set up for relocation by a trained professional.

1.Keep the washer in the upright position while removing the shipping bolts.

MAH22PDAGW0, MAH22PNAGW0 specifications

The Maytag MAH22PNAGW0 and MAH22PDAGW0 are high-efficiency front-loading washing machines that offer robust features and cutting-edge technologies designed to enhance your laundry experience. Known for their durability and performance, these models from Maytag are engineered to tackle tough stains and provide optimal cleaning results.

One of the standout features of both models is the PowerWash cycle, which utilizes a combination of extra agitation and a thorough rinse to effectively eliminate stubborn stains and deeply embedded dirt. This cycle ensures that your laundry comes out looking fresh and clean, even with heavily soiled items. Another key feature is the Heavy Duty cycle, which is specifically designed for washing bulky items and heavy fabrics, such as towels and bedding. This cycle provides the necessary cleaning power while being gentle on garments.

Both models also cater to user convenience through their advanced control panel featuring an intuitive interface. Users can easily select from various cycles, including Normal, Delicate, and Eco, allowing for flexibility based on laundry needs. The machines also feature a time-saving Quick Wash cycle, which delivers clean clothes in less time, making it ideal for busy households.

In terms of energy efficiency, the MAH22PNAGW0 and MAH22PDAGW0 are Energy Star certified, meaning they consume less water and electricity compared to traditional models. This efficiency not only leads to lower utility bills but also promotes a more sustainable lifestyle.

A notable characteristic of both washers is their stainless steel wash basket, which resists chipping and snagging, providing a gentle yet effective cleaning environment. The machines also come equipped with Maytag’s Direct Drive motor, which minimizes vibrations and noise, ensuring a quieter operation even during the spin cycle.

Additionally, the models offer a combination of a rear-drain pump and vented design, which helps to improve drainage and reduce the risk of mold and mildew buildup.

Overall, Maytag continues to uphold its reputation for reliability and quality with the MAH22PNAGW0 and MAH22PDAGW0, making these washing machines a great choice for any household looking for efficiency, power, and convenience in their laundry routine.