Safety precautions
Please plug the power plug on special | The washing machine must be positioned so that | |||
the plug is accessible. Be sure to pull the plug off | ||||
receptacle. Be sure to use | ||||
and close the water faucet in following cases: | ||||
power receptacle. Ensure that the earthing | ||||
prong of the power receptacle is earthed | power failure, delivering the machine, setting the | |||
reliably. Use leakage protector if possible. | machine idle or cleaning the machine. Do not plug | |||
|
|
| or pull the power plug with wet hand. | |
|
| Earth |
| |
|
|
|
| |
|
|
|
| |
|
|
|
| |
Do not bend ,extend,twist,bind by force.Do not press or nip it with weight. Keep the pin of the power plug clean,if the power plug is polluted with dust, please wipe with dry cloth carefully.
If the power cord or the power plug is bad, to avoid risk it is required to have it replaced by the technicians of our special shop or our customer care agent.
In case the washing machine is installed on ground with | Do not use water hotter than 50 . |
carpet, do not block the ventilation hole with carpet. |
|
T h e v e n t i l a t i o n holes at the bottom
Soft object
Do not put the machine at damp place like | Do not wash | |||
the bathroom. Never wash it with water. Do | ||||
the raincoat, bike covers etc. to avoid | ||||
not put wet laundries on the control panel. | ||||
abnormal vibrations in spinning. | ||||
|
|
| ||
|
|
|
| |
Do not let the machine share one receptacle with other electric appliances. If the plugging into the receptacle is loose, do not use the plug any more.
2
Trouble-shooting answer to question
(If there's breakdown, please pull off the power plug before checking) The following phenomena are not breakdowns sometimes. Please confirm again before sending it to repair. Do not repair it by yourself.
|
| Phenomena | The reason | How to settle | |
|
| Buzzing upon reservation starts, |
|
| |
|
|
|
| ||
|
| the digitron displays "E0" | The top lid is not closed | Close the top lid | |
|
|
|
|
|
|
|
| No or slow drain, the digitron | Is the drain hose put down? | Put down the drain hose. Open | |
|
| and close the top lid once. | |||
|
|
| |||
|
| displays "E1" , buzzing. | Is the drain hose blocked by | Clean the foreign material. | |
|
|
|
| foreign material? | |
|
|
|
| Open and close the top lid once. | |
|
|
|
|
| |
|
|
|
|
| |
|
| Running pauses during spin, | The top cover leaves open | Close the top lid | |
|
| the digitron displays "E2", | |||
|
|
|
| ||
|
| buzzing |
|
| |
|
|
|
|
| |
|
| Safety switch actuates, not | Are the laundries put slantingly? | ||
|
| spin, (after |
| top lid.Level the machine in right | |
|
| Is the machine slanting? | position. | ||
|
| twice), the digitron displays | |||
|
|
| Open and close the top lid once. | ||
|
| "E3", buzzing |
|
| |
|
|
|
|
|
|
|
| No or slow water filling (not | The water tap is not open | Open the water tap. | |
|
| Push the "Start/Pause" button. | |||
|
| reaching the level in 40 min), | The water inlet valve is blocked | Clean the water inlet valve. | |
|
| the digitron displays "E4", | The water pressureis too low | Push the "Start/Pause" button. | |
|
| Wait for the normal water pressure | |||
|
| buzzing | and the current is too small | ||
|
| Before use. | |||
|
|
|
|
| |
|
|
|
|
|
|
|
| The digitron displays E6. | The water level sensor is bad. | Please contact the | |
|
|
| service department. | ||
|
|
|
|
| |
|
| Poor or no waterfall flow | If the nozzle is choked with | Remove the foreign bodies | |
|
|
|
| foreign bodies |
|
|
|
|
|
|
|
|
|
|
| Is there power failure? | Use it when the power is on. |
|
|
| Not wash | Is the power plug loose? | Insert the power plug tightly. |
|
|
| Does the water level arrive at the | Affusion to the set water level. | |
|
| The machine does | |||
|
| set water level? |
| ||
|
| not act |
|
| |
|
|
|
|
| |
|
|
|
| Is the power plug loose? | Insert the power plug tightly. |
|
|
| Not spin | Is the top lid closed? | Close the top lid |
|
|
|
| ||
|
|
|
| Are the laundries put orderly? | Put the laundries orderly. |
|
| There's abnormal sound inside the | Is the machine slanting? | Level the machine properly. | |
|
| machine | Are the laundries slanting in | ||
|
|
|
| spinning? |
|
|
|
|
|
|
|
|
|
|
| Is the jointer screw of the water | Fasten the jointer screw |
|
| The water faucet leaks | inlet hose is loose or twisted | ||
|
| properly. | |||
|
|
|
| awry? | |
|
|
|
|
| |
|
|
|
|
|
|
Common phenomena |
|
|
Phenomena |
| Explanation |
The spinning is intermittent when it starts. |
| Balance the laundries to avoid slanting. |
| ||
|
|
|
The wash procedure pauses. |
| The cloth sensor is detecting , it will add water |
|
| after about 48 senconds. |
Select spin program, but it does not work. |
| The program is setting the drain time , certain |
| period is needed before it starts spinning. | |
|
| |
There may be some water flowing out of the |
| It is the water remained performance inspection |
drain hose in the first use of the machine. |
| by the factory. |
|
|
|