Safety precautions
Trouble-shooting answer to question
(If there's breakdown, please pull off the power plug before checking) The following phenomena are not breakdowns sometimes. Please confirm again before sending it to repair. Do not repair it by yourself.
Please plug the power plug on special receptacle. Be sure to use
Earth
The washing machine must be positioned so that the plug is accessible. Be sure to pull the plug off and close the water faucet in following cases: power failure, delivering the machine, setting the machine idle or cleaning the machine. Do not plug or pull the power plug with wet hand.
Phenomena | The reason | How to settle | |||
|
|
|
| ||
The digitron displays E0. | The top lid is opened during reserve procedure. | Close the top lid. | |||
|
|
|
|
|
|
The drainage cannot work, or is too slow. | Is the drain hose blocked? |
| Clean the foreign material. Open and close The top Lid Once. | ||
The digitron displays E1. |
| ||||
After long running of pump in the hot |
| ||||
| Some minutes later the machine will | ||||
| weather, power will be cut automati- |
| |||
|
| continue to work | |||
| cally for safe. |
| |||
|
|
|
|
| |
|
|
|
|
|
|
It stops running in midway. The digitron | The top lid is not closed. |
| Close the top lid. | ||
displays E2. |
| ||||
|
|
|
|
| |
|
|
|
|
| |
The safety switch acts, and the | Are the laundries put slantingly? | Reorder the laundries.Close the top lid. | |||
spinning cannot work. The | Is the machine slanting? |
| Th machine will start running after 10 | ||
|
| seconds of being placed horizontally. | |||
Do not bend ,extend,twist,bind by force.Do not press or nip it with weight. Keep the pin of the power plug clean,if the power plug is polluted with dust, please wipe with dry cloth carefully.
If the power cord or the power plug is bad, to avoid risk it is required to have it replaced by the technicians of our special shop or our customer care agent.
In case the washing machine is installed on ground with | Do not use water hotter than 50 . |
carpet, do not block the ventilation hole with carpet. |
|
T h e v e n t i l a t i o n holes at the bottom
Carpet
Do not put the machine at damp place like | Do not wash | |||
the raincoat, bike covers etc. to avoid | ||||
the bathroom. Never wash it with water. Do | ||||
not put wet laundries on the control panel. | abnormal vibrations in spinning and | |||
|
|
| damages to the laundries. | |
|
|
|
| |
Do not let the machine share one receptacle with other electric appliances. If the plugging into the receptacle is loose, do not use the plug any more.
2
digitron displays E3. |
|
|
| |
|
|
|
|
|
The water filling does not work, or is | Is the water tap opened, or is there water | Open the water tap. Push the start/Pause |
| |
supply failure? | button once. |
| ||
slow. After a period of time, the digital |
| |||
Is the water inlet valve blocked? | Clean the water inlet valve then push |
| ||
displays E4. |
| |||
Is the water pressure too low? | the start/Pause button once. |
| ||
|
| Push the Start/Pause button once. |
| |
|
|
|
| |
|
|
|
|
|
The digitron displays E6. | The water level sensor is bad. | Please contact the customer care |
| |
agent. |
| |||
|
|
|
| |
| Not wash | Is there power failure? | Please use it when there's power supply. |
|
| Is the power plug inserted tightly? | Insert the power plug tightly. |
| |
The machine does |
| Is the water level reached preset position? | Fill water to the preset position. |
|
|
|
|
| |
not act |
| Is the power plug inserted tightly? | Insert the power plug tightly. |
|
| Not spin |
| ||
| Is the top lid closed reliably? | Close the top lid. |
| |
|
| Are the laundries set flat? | Set the laundries flat. |
|
|
|
|
|
|
There's abnormal sound | Is the machine slanting? | Adjust the machine to be even |
| |
Reorder the laundries and close the top lid. |
| |||
inside the machine | Are the laundries put slantingly in spinning? |
| ||
Remove the foreign materials. |
| |||
Are there any foreign materials? |
| |||
|
|
| ||
|
|
|
|
|
The water faucet leaks | Is the jointer of water inlet hose loose | Fasten the jointer properly. |
| |
or awry? |
|
| ||
|
|
|
| |
Common phenomena
Phenomena |
| Explanation |
The spinning is intermittent when it starts. |
| Balance the laundries to avoid slanting. |
| ||
|
|
|
The wash procedure is paused. |
| The cloth sensor is checking the cloth, it willadd waterafter 48 seconds. |
|
|
|
Push the SPIN button , but it doesn't work. |
| The program is setting the drain time. Some time is needed |
|
| before it starts spinning. |
|
|
|
The pulsator pauses during water inlet |
| It is to avoid splashing during water inlet. |
in wash and rinse. |
|
|
|
|
|
There may be some water flowing out of the |
| It is the water remained in the factory inspection of performance. |
drain hose in the first use of the machine. |
| |
|
| |
|
|
|