American Dryer Corp WDA-385 Electrical and Gas Requirements, Operational Service Check Procedure

Page 11

B. Electrical and Gas Requirements

It is your responsibility to have ALL electrical connections made by a properly licensed and competent electrician to assure that the electrical installation is adequate and conforms with local and state regula- tions or codes. In the absence of such codes, ALL electrical connections, material, and workmanship must conform to the applicable requirements of the National Electric Code ANSI/NFPA No. 70-LATEST EDITION.

IMPORTANT: Failure to comply with these codes or ordinances and/or the requirements stipulated in this manual can result in PERSONAL INJURY OR COMPONENT FAILURE.

The dryer installation must meet the AMERICAN NATIONAL STANDARD, National Fuel Gas Code ANSI Z223.1-LATEST EDITION, as well as, local codes and ordinances, and must be done by a qualified technician.

NOTE: Undersized gas piping will result in ignition problems and slow drying and can create a safety hazard.

The dryer must be connected to the type of gas (natural or L.P.) indicated on the dryer data label. If this information does not agree with the type of gas available, contact the distributor who sold the dryer or contact the factory.

The gas input ratings shown on the dryer data label are for elevations up to 2,000 feet, unless elevation requirements of over 2,000 feet were specified at the time the dryer order was placed with the factory. The adjustment for dryers in the field for elevations over 2,000 feet are made by changing the burner orifices. If this adjustment is necessary, contact the distributor who sold the dryer or contact the factory.

NOTE: Any burner changes must be made by a qualified technician.

C. Operational Service Check Procedure

After performing any service or maintenance function, an operational check should be performed to insure that ALL components are performing properly.

1.Make a complete operational check of ALL the operating controls to insure that the timing is correct, temperature selection switches are functioning properly.

2.Make a complete operational check of ALL safety related circuits, door switch(es), hi-limit thermostat, sail switch, cycling thermostats, etc.

3.On gas models, gas pressure test should be taken at the gas valve pressure tap of each dryer to assure that the water column pressure is correct and consistent.

NOTE: Water column pressure requirements: (measured at the pressure tap on the gas valve body.) Natural Gas - 3.5 to 4 inches W.C.L.P. Gas - 10.5 to 11 inches W.C.

7

Page 10 Page 12
Image 11
Page 10 Page 12
Contents ADG-385/WDA-385 Important Note to Purchaser Retain This Manual In a Safe Place For Future ReferencePage For Your Safety Table of Contents Technical Information Important Information Safety PrecautionsCleaning Routine MaintenanceLubrication AdjustmentsEnclosure, Air Supply, and Exhaust Requirements Installation RequirementsElectrical and Gas Requirements Operational Service Check ProcedurePage Coin Box and Vault Description of PartsControl Panel Control BoxTumbler Main Door SwitchLint Coop Idler Bearing Motor AssemblyTumbler Bearing and Pulley Arrangement Sail Switch Temperature SensorsHi-Limit Thermostat Motor Contactor 1Ø MotorNon-Reversing Contactor 3Ø Motor Servicing To Replace Control Panel AssemblyTo Replace Keypad refer to illustration above To Replace ComputerTo Replace Coin Acceptor To Remove Optic SwitchTo Replace Motor Contactor 2-Pole, 24VAC To Replace Microprocessor Temperature Sensor ProbeBurner Controls Gas To Replace Gas Valve To Replace Spark IgnitorTo Test and Adjust Gas Water Column Pressure To Replace Main Burner Orifices See Chart On FollowingTo Replace Burner Tubes To Replace DSI Module To Remove The Temperature Sensor or High Heat Protector To Replace Sail Switch Sail Switch AssemblyTo Replace Main Door Assembly Steel Door To Adjust Sail SwitchTo Install NEW Main Door Glass To Replace Front Panel Page Important Loctite NOW Being Used To Replace Rear Tumbler BearingTo Replace The Front Tumbler Bearing To Replace Idler Pulley Idler and Bearing AssemblyDrive Pulley To Replace Idler BearingTumbler Alignment lateral Tumbler basket Tumbler Alignment verticalTo Replace The Tumbler and/or Tumbler Support Important Loctite NOW Being Used Belt Tension Alignment Motor To Idler Belt Tension Adjustment-Tumbler To IdlerBelts refer to illustration in Sections I, J and K Impeller Lintscreen To Replace Lintscreen To Replace V-BeltsMotor To Replace Motor Diagnostic L.E.D. Display Failure Codes Trouble ShootingPhase 5 Coin System Diagnostics Microprocessor Controller Relay Output L.E.D. Indicators D. Display IndicatorsPage No Heat Condition Page No Start Condition No Display Condition Page DSFL Display Condition DOOr Display Condition Data Label Technical InformationUsing a Manometer Clcc E.D. Display CodesComputer Logic and Wiring Diagram Page ADC450179 01/08/98-50 05/21/98-50

WDA-385 specifications

The American Dryer Corp WDA-385 is a high-efficiency commercial washer designed to meet the demanding needs of laundries, fitness centers, hotels, and other facilities requiring robust laundry solutions. Known for its reliability and performance, the WDA-385 has quickly gained recognition in the laundry industry for its advanced features and technologies.

One of the standout features of the WDA-385 is its impressive capacity. With a drum size designed to handle large loads, it allows users to process more laundry in a single cycle, increasing operational efficiency. This capability is especially beneficial for establishments with high laundry demands, as it reduces the number of cycles required and saves valuable time.

The WDA-385 employs a state-of-the-art microprocessor control system that offers user-friendly programming. This technology allows for customizable wash cycles and options, ensuring that different types of fabrics and soiling levels are adequately addressed. Operators can choose from a variety of preset programs or create their own, providing flexibility in the washing process.

Energy efficiency is another key characteristic of the WDA-385. The washer is designed to minimize water and detergent consumption without compromising cleaning performance. By incorporating technologies that optimize water usage and enhance spin efficiency, the WDA-385 helps facilities reduce their utility costs and environmental footprint. This makes it an ideal choice for eco-conscious businesses looking to enhance their sustainability efforts.

Durability and construction quality are also notable features of the WDA-385. Built with heavy-duty components, it is designed to withstand the rigors of continuous use in commercial settings. The stainless steel drum and front panel not only guarantee longevity but also ensure that the unit is easy to clean and maintain.

Furthermore, the WDA-385 incorporates advanced safety features such as a door lock system that prevents accidental openings during operation, ensuring user safety and preventing leaks. Its quiet operation and vibration reduction technology make it suitable for locations where noise levels need to be minimized.

In summary, the American Dryer Corp WDA-385 is a versatile and dependable commercial washing machine that combines advanced technology with practical features. Its robust construction, energy efficiency, and customizable programming make it an excellent choice for businesses looking to enhance their laundry operations. Whether in a hotel, gym, or laundry facility, the WDA-385 delivers exceptional washing performance while keeping operational costs in check.
Top Page Image Contents