American Dryer Corp WDA-385 service manual To Replace Spark Ignitor, To Replace Gas Valve

Page 23

To Replace Spark Ignitor

1. Discontinue power to dryer.

2.Disconnect HV connector and flame probe connection from ignitor.

3.Disassemble ignitor from burner by removing

the two (2) self-tapping screws.

4. Reverse procedure for installing new ignitor probe.

NOTE: Before re-establishing power to dryer, visually check the following: (see illustration)

1.The flame probe, ignitor probe, and ground rod are ALL on the same line of axis.

2.There should be a 1/8" gap (+/-, 1/32) between the ignitor probe and ground rod.

3.Do not wrap the red HV wire and flame probe wire together. (Improper operation may result.) They

may run along side each other.

To Replace Gas Valve

1. Discontinue power to dryer.

2. Close shut off valve in gas supply line.

3. Disconnect gas valve wiring.

4. Break union connection before gas valve.

5. Loosen and remove two (2) screws securing pipe bracket to the burner.

6.Remove gas valve / manifold assembly from the dryer.

7.Remove manifold from output of the gas valve.

8.Remove union tail piece from valve. Use a 1/2" allen wrench (ADC P/N: 410001)

9.Reverse procedure for installing new gas valve.

WARNING: Test ALL connections for leaks by brushing on a soapy water solution (Never Test For Leaks With A Flame)

19

Page 22 Page 24
Image 23
Page 22 Page 24
Contents ADG-385/WDA-385 Important Note to Purchaser Retain This Manual In a Safe Place For Future ReferencePage For Your Safety Table of Contents Technical Information Important Information Safety PrecautionsCleaning Routine MaintenanceLubrication AdjustmentsEnclosure, Air Supply, and Exhaust Requirements Installation RequirementsElectrical and Gas Requirements Operational Service Check ProcedurePage Coin Box and Vault Description of PartsControl Panel Control BoxTumbler Main Door SwitchLint Coop Idler Bearing Motor AssemblyTumbler Bearing and Pulley Arrangement Sail Switch Temperature SensorsHi-Limit Thermostat Motor Contactor 1Ø MotorNon-Reversing Contactor 3Ø Motor Servicing To Replace Control Panel AssemblyTo Replace Keypad refer to illustration above To Replace ComputerTo Replace Coin Acceptor To Remove Optic SwitchTo Replace Motor Contactor 2-Pole, 24VAC To Replace Microprocessor Temperature Sensor ProbeBurner Controls Gas To Replace Gas Valve To Replace Spark IgnitorTo Test and Adjust Gas Water Column Pressure To Replace Main Burner Orifices See Chart On FollowingTo Replace Burner Tubes To Replace DSI Module To Remove The Temperature Sensor or High Heat Protector To Replace Sail Switch Sail Switch AssemblyTo Replace Main Door Assembly Steel Door To Adjust Sail SwitchTo Install NEW Main Door Glass To Replace Front Panel Page Important Loctite NOW Being Used To Replace Rear Tumbler BearingTo Replace The Front Tumbler Bearing To Replace Idler Pulley Idler and Bearing AssemblyDrive Pulley To Replace Idler BearingTumbler Alignment lateral Tumbler basket Tumbler Alignment verticalTo Replace The Tumbler and/or Tumbler Support Important Loctite NOW Being Used Belt Tension Alignment Motor To Idler Belt Tension Adjustment-Tumbler To IdlerBelts refer to illustration in Sections I, J and K Impeller Lintscreen To Replace Lintscreen To Replace V-BeltsMotor To Replace Motor Diagnostic L.E.D. Display Failure Codes Trouble ShootingPhase 5 Coin System Diagnostics Microprocessor Controller Relay Output L.E.D. Indicators D. Display IndicatorsPage No Heat Condition Page No Start Condition No Display Condition Page DSFL Display Condition DOOr Display Condition Data Label Technical InformationUsing a Manometer Clcc E.D. Display CodesComputer Logic and Wiring Diagram Page ADC450179 01/08/98-50 05/21/98-50

WDA-385 specifications

The American Dryer Corp WDA-385 is a high-efficiency commercial washer designed to meet the demanding needs of laundries, fitness centers, hotels, and other facilities requiring robust laundry solutions. Known for its reliability and performance, the WDA-385 has quickly gained recognition in the laundry industry for its advanced features and technologies.

One of the standout features of the WDA-385 is its impressive capacity. With a drum size designed to handle large loads, it allows users to process more laundry in a single cycle, increasing operational efficiency. This capability is especially beneficial for establishments with high laundry demands, as it reduces the number of cycles required and saves valuable time.

The WDA-385 employs a state-of-the-art microprocessor control system that offers user-friendly programming. This technology allows for customizable wash cycles and options, ensuring that different types of fabrics and soiling levels are adequately addressed. Operators can choose from a variety of preset programs or create their own, providing flexibility in the washing process.

Energy efficiency is another key characteristic of the WDA-385. The washer is designed to minimize water and detergent consumption without compromising cleaning performance. By incorporating technologies that optimize water usage and enhance spin efficiency, the WDA-385 helps facilities reduce their utility costs and environmental footprint. This makes it an ideal choice for eco-conscious businesses looking to enhance their sustainability efforts.

Durability and construction quality are also notable features of the WDA-385. Built with heavy-duty components, it is designed to withstand the rigors of continuous use in commercial settings. The stainless steel drum and front panel not only guarantee longevity but also ensure that the unit is easy to clean and maintain.

Furthermore, the WDA-385 incorporates advanced safety features such as a door lock system that prevents accidental openings during operation, ensuring user safety and preventing leaks. Its quiet operation and vibration reduction technology make it suitable for locations where noise levels need to be minimized.

In summary, the American Dryer Corp WDA-385 is a versatile and dependable commercial washing machine that combines advanced technology with practical features. Its robust construction, energy efficiency, and customizable programming make it an excellent choice for businesses looking to enhance their laundry operations. Whether in a hotel, gym, or laundry facility, the WDA-385 delivers exceptional washing performance while keeping operational costs in check.
Top Page Image Contents