American Dryer Corp WDA-385 service manual To Remove The Temperature Sensor or High Heat Protector

Page 27

To Remove The Temperature Sensor or High Heat Protector

A.High Heat Protector

1.Discontinue power to dryer.

2.Open and remove lint door.

3.Locate temperature sensor bracket assembly under the basket. Loosen the two phillips head screws. Disconnect the connector.

4.Slide bracket toward rear of the machine and remove the bracket assembly from the dryer.

5.At this point you have access to remove either the high heat protector or the temperature sensor.

6.To remove the high heat protection remove the two (2) screws, washers, and nuts holding the high heat protector in place.

7.Remove the high heat protector.

8.Reverse procedure for installation of new high heat protector.

B.Temperature Sensor

1.Discontinue power to dryer.

2.Open and remove lint door.

3.Disconnect sensor bracket harness connector.

4.Loosen the two (2) phillips head screws securing bracket assembly to dryer and remove by sliding bracket towards the rear of the dryer.

5.Disassemble sensor probe from bracket assembly by removing the top push-on fastener securing the probe to the basket.

6.Disconnect the two (2) orange wires from the high heat temperature thermostat remove the four (4) position connector, wires, and probe from the bracket assembly.

7.Install new probe assembly (ADC P/N: 880251) by reversing procedure.

23

Page 26 Page 28
Image 27
Page 26 Page 28
Contents ADG-385/WDA-385 Important Note to Purchaser Retain This Manual In a Safe Place For Future ReferencePage For Your Safety Table of Contents Technical Information Important Information Safety PrecautionsCleaning Routine MaintenanceLubrication AdjustmentsEnclosure, Air Supply, and Exhaust Requirements Installation RequirementsElectrical and Gas Requirements Operational Service Check ProcedurePage Coin Box and Vault Description of PartsControl Panel Control BoxMain Door Switch Lint CoopTumbler Motor Assembly Tumbler Bearing and Pulley ArrangementIdler Bearing Sail Switch Temperature SensorsMotor Contactor 1Ø Motor Non-Reversing Contactor 3Ø MotorHi-Limit Thermostat Servicing To Replace Control Panel AssemblyTo Replace Keypad refer to illustration above To Replace ComputerTo Replace Coin Acceptor To Remove Optic SwitchTo Replace Motor Contactor 2-Pole, 24VAC To Replace Microprocessor Temperature Sensor ProbeBurner Controls Gas To Replace Gas Valve To Replace Spark IgnitorTo Test and Adjust Gas Water Column Pressure To Replace Main Burner Orifices See Chart On FollowingTo Replace Burner Tubes To Replace DSI Module To Remove The Temperature Sensor or High Heat Protector To Replace Sail Switch Sail Switch AssemblyTo Replace Main Door Assembly Steel Door To Adjust Sail SwitchTo Install NEW Main Door Glass To Replace Front Panel Page Important Loctite NOW Being Used To Replace Rear Tumbler BearingTo Replace The Front Tumbler Bearing To Replace Idler Pulley Idler and Bearing AssemblyDrive Pulley To Replace Idler BearingTumbler Alignment lateral Tumbler basket Tumbler Alignment verticalTo Replace The Tumbler and/or Tumbler Support Important Loctite NOW Being Used Belt Tension Adjustment-Tumbler To Idler Belts refer to illustration in Sections I, J and KBelt Tension Alignment Motor To Idler To Replace V-Belts Motor To Replace MotorImpeller Lintscreen To Replace Lintscreen Trouble Shooting Phase 5 Coin System DiagnosticsDiagnostic L.E.D. Display Failure Codes Microprocessor Controller Relay Output L.E.D. Indicators D. Display IndicatorsPage No Heat Condition Page No Start Condition No Display Condition Page DSFL Display Condition DOOr Display Condition Data Label Technical InformationUsing a Manometer Clcc E.D. Display CodesComputer Logic and Wiring Diagram Page ADC450179 01/08/98-50 05/21/98-50

WDA-385 specifications

The American Dryer Corp WDA-385 is a high-efficiency commercial washer designed to meet the demanding needs of laundries, fitness centers, hotels, and other facilities requiring robust laundry solutions. Known for its reliability and performance, the WDA-385 has quickly gained recognition in the laundry industry for its advanced features and technologies.

One of the standout features of the WDA-385 is its impressive capacity. With a drum size designed to handle large loads, it allows users to process more laundry in a single cycle, increasing operational efficiency. This capability is especially beneficial for establishments with high laundry demands, as it reduces the number of cycles required and saves valuable time.

The WDA-385 employs a state-of-the-art microprocessor control system that offers user-friendly programming. This technology allows for customizable wash cycles and options, ensuring that different types of fabrics and soiling levels are adequately addressed. Operators can choose from a variety of preset programs or create their own, providing flexibility in the washing process.

Energy efficiency is another key characteristic of the WDA-385. The washer is designed to minimize water and detergent consumption without compromising cleaning performance. By incorporating technologies that optimize water usage and enhance spin efficiency, the WDA-385 helps facilities reduce their utility costs and environmental footprint. This makes it an ideal choice for eco-conscious businesses looking to enhance their sustainability efforts.

Durability and construction quality are also notable features of the WDA-385. Built with heavy-duty components, it is designed to withstand the rigors of continuous use in commercial settings. The stainless steel drum and front panel not only guarantee longevity but also ensure that the unit is easy to clean and maintain.

Furthermore, the WDA-385 incorporates advanced safety features such as a door lock system that prevents accidental openings during operation, ensuring user safety and preventing leaks. Its quiet operation and vibration reduction technology make it suitable for locations where noise levels need to be minimized.

In summary, the American Dryer Corp WDA-385 is a versatile and dependable commercial washing machine that combines advanced technology with practical features. Its robust construction, energy efficiency, and customizable programming make it an excellent choice for businesses looking to enhance their laundry operations. Whether in a hotel, gym, or laundry facility, the WDA-385 delivers exceptional washing performance while keeping operational costs in check.
Top Page Image Contents