American Dryer Corp WDA-385 service manual Idler and Bearing Assembly, To Replace Idler Pulley

Page 35

F. Idler and Bearing Assembly

(Remove backguard to access assembly.)

To Replace Idler Pulley

1. Remove backguard.

2. Loosen v-belts, then rotate pulley and roll v-belts out of grooves.

3. Loosen the two (2) set screws on the pulley and pull off the shaft.

4. Reverse procedure for installing new idler pulley.

NOTE: Check tension and alignment of belts before operating dryer.

IMPORTANT: LOCTITE® NOW BEING USED.

Effective January 24, 1996, LOCTITE® is being used on the ADG-385/WDA-385 dryer. LOCTITE® is being applied toALL beaaring set screws, used onALL basket (tumbler) shafts, ALL idler shafts,ALL impellor (fan/ blower) shafts, and ALL drive shaft bearings.

A yellow label (ADC Part No. 112801) is affixed to the dryer to inform customers of the use of LOCTITE®. This label is shown immediately below;

IMPORTANT

LOCTITE® ADHESIVE HAS BEEN USED

TO SECURE SET SCREWS AND BEARINGS

IN PLACE. ONCE SET SCREWS HAVE BEEN

REMOVED, A GEAR PULLER MAY BE NECES-

SARY TO REMOVE BEARING TO AVOID DAMAGE.

P/N: 112801

One (1) of these labels is attached to each Tumbler (basket) Bearing Assembly (pillow block bearing box) on the ADG-385/WDA-385 dryer.

Should readjustment or removal of set screws become necessary in the field and the process becomes difficult, apply heat to the set screw with a soldering gun (450º F) for a few minutes.

31

Page 34 Page 36
Image 35
Page 34 Page 36
Contents ADG-385/WDA-385 Important Note to Purchaser Retain This Manual In a Safe Place For Future ReferencePage For Your Safety Table of Contents Technical Information Important Information Safety PrecautionsCleaning Routine MaintenanceLubrication AdjustmentsEnclosure, Air Supply, and Exhaust Requirements Installation RequirementsElectrical and Gas Requirements Operational Service Check ProcedurePage Coin Box and Vault Description of PartsControl Panel Control BoxTumbler Main Door SwitchLint Coop Idler Bearing Motor AssemblyTumbler Bearing and Pulley Arrangement Sail Switch Temperature SensorsHi-Limit Thermostat Motor Contactor 1Ø MotorNon-Reversing Contactor 3Ø Motor Servicing To Replace Control Panel AssemblyTo Replace Keypad refer to illustration above To Replace ComputerTo Replace Coin Acceptor To Remove Optic SwitchTo Replace Motor Contactor 2-Pole, 24VAC To Replace Microprocessor Temperature Sensor ProbeBurner Controls Gas To Replace Gas Valve To Replace Spark IgnitorTo Test and Adjust Gas Water Column Pressure To Replace Main Burner Orifices See Chart On FollowingTo Replace Burner Tubes To Replace DSI Module To Remove The Temperature Sensor or High Heat Protector To Replace Sail Switch Sail Switch AssemblyTo Replace Main Door Assembly Steel Door To Adjust Sail SwitchTo Install NEW Main Door Glass To Replace Front Panel Page Important Loctite NOW Being Used To Replace Rear Tumbler BearingTo Replace The Front Tumbler Bearing To Replace Idler Pulley Idler and Bearing AssemblyDrive Pulley To Replace Idler BearingTumbler Alignment lateral Tumbler basket Tumbler Alignment verticalTo Replace The Tumbler and/or Tumbler Support Important Loctite NOW Being Used Belt Tension Alignment Motor To Idler Belt Tension Adjustment-Tumbler To IdlerBelts refer to illustration in Sections I, J and K Impeller Lintscreen To Replace Lintscreen To Replace V-BeltsMotor To Replace Motor Diagnostic L.E.D. Display Failure Codes Trouble ShootingPhase 5 Coin System Diagnostics Microprocessor Controller Relay Output L.E.D. Indicators D. Display IndicatorsPage No Heat Condition Page No Start Condition No Display Condition Page DSFL Display Condition DOOr Display Condition Data Label Technical InformationUsing a Manometer Clcc E.D. Display CodesComputer Logic and Wiring Diagram Page ADC450179 01/08/98-50 05/21/98-50

WDA-385 specifications

The American Dryer Corp WDA-385 is a high-efficiency commercial washer designed to meet the demanding needs of laundries, fitness centers, hotels, and other facilities requiring robust laundry solutions. Known for its reliability and performance, the WDA-385 has quickly gained recognition in the laundry industry for its advanced features and technologies.

One of the standout features of the WDA-385 is its impressive capacity. With a drum size designed to handle large loads, it allows users to process more laundry in a single cycle, increasing operational efficiency. This capability is especially beneficial for establishments with high laundry demands, as it reduces the number of cycles required and saves valuable time.

The WDA-385 employs a state-of-the-art microprocessor control system that offers user-friendly programming. This technology allows for customizable wash cycles and options, ensuring that different types of fabrics and soiling levels are adequately addressed. Operators can choose from a variety of preset programs or create their own, providing flexibility in the washing process.

Energy efficiency is another key characteristic of the WDA-385. The washer is designed to minimize water and detergent consumption without compromising cleaning performance. By incorporating technologies that optimize water usage and enhance spin efficiency, the WDA-385 helps facilities reduce their utility costs and environmental footprint. This makes it an ideal choice for eco-conscious businesses looking to enhance their sustainability efforts.

Durability and construction quality are also notable features of the WDA-385. Built with heavy-duty components, it is designed to withstand the rigors of continuous use in commercial settings. The stainless steel drum and front panel not only guarantee longevity but also ensure that the unit is easy to clean and maintain.

Furthermore, the WDA-385 incorporates advanced safety features such as a door lock system that prevents accidental openings during operation, ensuring user safety and preventing leaks. Its quiet operation and vibration reduction technology make it suitable for locations where noise levels need to be minimized.

In summary, the American Dryer Corp WDA-385 is a versatile and dependable commercial washing machine that combines advanced technology with practical features. Its robust construction, energy efficiency, and customizable programming make it an excellent choice for businesses looking to enhance their laundry operations. Whether in a hotel, gym, or laundry facility, the WDA-385 delivers exceptional washing performance while keeping operational costs in check.
Top Page Image Contents