American Dryer Corp WDA-385 service manual Servicing, To Replace Control Panel Assembly

Page 18

SECTION V

Servicing

ALL electrical/mechanical service or repairs should be made with the electrical power to the dryer disconnected (power off).

WARNING: PERSONAL INJURY COULD RESULT

The information provided in this section should not be misconstrued as a device for use by an untrained person making repairs. Service work should be performed by competent technicians in accordance with local, state, and federal codes.

When contacting the factory for assistance, always have the dryer model and serial numbers available.

CAUTION: Observe ALL safety precautions displayed on the dryer or specified in this manual before and while making repairs.

Before considering replacement, make sure that ALL connectors are in place and making proper contact. Check input voltages and temperature sensor. After replacing any parts or performing adjustments or service run through a complete cycle.

To Replace Control Panel Assembly

1. Disconnect power to the dryer.

2. Disconnect main power harness from rear of computer by squeezing locking tab and pulling connector straight back.

3. Disconnect the green ground wire from the computer.

4. Disconnect coin acceptor optic switch connector from 15 pin harness.

5. To remove control panel assembly from the control box, gently tap the bottom of the control panel upward and lift off the hinges.

6. Install new control panel assembly by reversing this procedure.

7. Be sure to check or reset programs.

NOTE: Use caution when handling MP Controller. Easily damaged by static electricity.

14

Page 17 Page 19
Image 18
Page 17 Page 19
Contents ADG-385/WDA-385 Retain This Manual In a Safe Place For Future Reference Important Note to PurchaserPage For Your Safety Table of Contents Technical Information Safety Precautions Important InformationRoutine Maintenance CleaningAdjustments LubricationInstallation Requirements Enclosure, Air Supply, and Exhaust RequirementsOperational Service Check Procedure Electrical and Gas RequirementsPage Control Box Description of PartsControl Panel Coin Box and VaultMain Door Switch Lint CoopTumbler Motor Assembly Tumbler Bearing and Pulley ArrangementIdler Bearing Temperature Sensors Sail SwitchMotor Contactor 1Ø Motor Non-Reversing Contactor 3Ø MotorHi-Limit Thermostat To Replace Control Panel Assembly ServicingTo Replace Computer To Replace Keypad refer to illustration aboveTo Remove Optic Switch To Replace Coin AcceptorTo Replace Microprocessor Temperature Sensor Probe To Replace Motor Contactor 2-Pole, 24VACBurner Controls Gas To Replace Spark Ignitor To Replace Gas ValveTo Replace Main Burner Orifices See Chart On Following To Test and Adjust Gas Water Column PressureTo Replace Burner Tubes To Replace DSI Module To Remove The Temperature Sensor or High Heat Protector Sail Switch Assembly To Replace Sail SwitchTo Adjust Sail Switch To Replace Main Door Assembly Steel DoorTo Install NEW Main Door Glass To Replace Front Panel Page To Replace Rear Tumbler Bearing Important Loctite NOW Being UsedTo Replace The Front Tumbler Bearing Idler and Bearing Assembly To Replace Idler PulleyTo Replace Idler Bearing Drive PulleyTumbler basket Tumbler Alignment vertical Tumbler Alignment lateralTo Replace The Tumbler and/or Tumbler Support Important Loctite NOW Being Used Belt Tension Adjustment-Tumbler To Idler Belts refer to illustration in Sections I, J and KBelt Tension Alignment Motor To Idler To Replace V-Belts Motor To Replace MotorImpeller Lintscreen To Replace Lintscreen Trouble Shooting Phase 5 Coin System DiagnosticsDiagnostic L.E.D. Display Failure Codes D. Display Indicators Microprocessor Controller Relay Output L.E.D. IndicatorsPage No Heat Condition Page No Start Condition No Display Condition Page DSFL Display Condition DOOr Display Condition Technical Information Data LabelUsing a Manometer E.D. Display Codes ClccComputer Logic and Wiring Diagram Page ADC450179 01/08/98-50 05/21/98-50

WDA-385 specifications

The American Dryer Corp WDA-385 is a high-efficiency commercial washer designed to meet the demanding needs of laundries, fitness centers, hotels, and other facilities requiring robust laundry solutions. Known for its reliability and performance, the WDA-385 has quickly gained recognition in the laundry industry for its advanced features and technologies.

One of the standout features of the WDA-385 is its impressive capacity. With a drum size designed to handle large loads, it allows users to process more laundry in a single cycle, increasing operational efficiency. This capability is especially beneficial for establishments with high laundry demands, as it reduces the number of cycles required and saves valuable time.

The WDA-385 employs a state-of-the-art microprocessor control system that offers user-friendly programming. This technology allows for customizable wash cycles and options, ensuring that different types of fabrics and soiling levels are adequately addressed. Operators can choose from a variety of preset programs or create their own, providing flexibility in the washing process.

Energy efficiency is another key characteristic of the WDA-385. The washer is designed to minimize water and detergent consumption without compromising cleaning performance. By incorporating technologies that optimize water usage and enhance spin efficiency, the WDA-385 helps facilities reduce their utility costs and environmental footprint. This makes it an ideal choice for eco-conscious businesses looking to enhance their sustainability efforts.

Durability and construction quality are also notable features of the WDA-385. Built with heavy-duty components, it is designed to withstand the rigors of continuous use in commercial settings. The stainless steel drum and front panel not only guarantee longevity but also ensure that the unit is easy to clean and maintain.

Furthermore, the WDA-385 incorporates advanced safety features such as a door lock system that prevents accidental openings during operation, ensuring user safety and preventing leaks. Its quiet operation and vibration reduction technology make it suitable for locations where noise levels need to be minimized.

In summary, the American Dryer Corp WDA-385 is a versatile and dependable commercial washing machine that combines advanced technology with practical features. Its robust construction, energy efficiency, and customizable programming make it an excellent choice for businesses looking to enhance their laundry operations. Whether in a hotel, gym, or laundry facility, the WDA-385 delivers exceptional washing performance while keeping operational costs in check.
Top Page Image Contents