American Dryer Corp ML-55HS installation manual Steam Information

Page 32

NOTE: A water column (W.C.) test pressure of 3.5 inches (8.7 mb) for natural gas and 10.5 inches (26.1 mb) for liquid propane (L.P.) dryers is required at the gas valve pressure tap of each dryer for proper and safe operation.

A 1/8" N.P.T. plugged tap, accessible for a test gauge connection, must be installed in the main gas supply line immediately upstream of each dryer.

IMPORTANT: Pipe joint compounds that resist the action of natural gas and L.P. gas must be used.

IMPORTANT: Test ALL connections for leaks by brushing on a soapy water solution (liquid detergent works well).

WARNING: NEVER TEST FOR LEAKS WITH A FLAME!!!

ALL components/materials must conform to National Fuel Gas Code Specifications ANSI Z223.1-LATEST EDITION, or in Canada, CAN/CGA-B149.1-M91 (Natural Gas) or CAN/CGA-B149.2-M91 (L.P. Gas) or LATEST EDITION (for General Installation and Gas Plumbing), as well as local codes and ordinances and must be done by a qualified professional. It is important that gas pressure regulators meet applicable pressure requirements, and that gas meters be rated for the total amount of ALL the appliance BTUs being supplied.

IMPORTANT: The dryer and its individual shutoff valve must be disconnected from the gas supply piping system during any pressure testing of that system at test pressures in excess of 1/2 psig (3.5 kPa).

NOTE: The dryer must be isolated from the gas supply piping system by closing its individual manual shutoff valve during any pressure test of the gas supply system at test pressures equal to or less than 1/2 psig (3.5 kPa).

H. STEAM INFORMATION

It is your responsibility to have ALL plumbing connections made by a qualified professional to assure that the steam plumbing installation is adequate and conforms with local and state regulations or codes.

IMPORTANT: Failure to comply with the requirements stipulated in this manual can result in

component failure which will VOID THE WARRANTY.

NOTE: The MLS-55 is manufactured with a pneumatic (piston) damper system, which requires an external supply of air (80 PSI ± 10 PSI [5.52 bars ± 0.68 bars]).

1.Steam Coil PH Level

The normal PH level for copper type steam coils must be maintained between a value of 8.5 to 9.5. For steel type steam coils the PH level must be maintained between a value of 9.5 to 10.5. These limits are set to limit the acid attack of the steam coils.

IMPORTANT: Coil failure due to improper PH level will VOID THE WARRANTY.

28

Page 31 Page 33
Image 32
Page 31 Page 33
Contents ML-55HS Retain This Manual In a Safe Place For Future Reference For Your Safety Page Table of Contents Section Procedure for Functional Check of Replacement Section Important InformationSafety Precautions What to do if YOU Smell GASStandards SPECIFICATIONS/COMPONENT Identification SpecificationsSpecifications Component Identification Electric Service Relay Box Installation Procedures Location RequirementsUNPACKING/SETTING UP Dryer Enclosure Requirements Fresh AIR Requirements Exhaust Requirements Create a Potential Fire HazardPage Page Page Electrical Information MLG-55 Gas MLS-55 Steam Page Black White Green Positive Neutral Ground Page Page Page GAS Information Type of GAS Page Steam Information Operating Steam Pressure Page Bars Steam System Operation Page Preparation for OPERATION/START-UP Preoperational Tests Basket Coating Preoperational Instructions Shut Down Instructions Parts SERVICE/PARTS InformationService Warranty Information Returning Warranty CardsWarranty Returning Warranty PartsPage Routine Maintenance CleaningAdjustments LubricationProcedure for Functional Check Replacement Components Page Page Reversing Timer SPIN/DWELL Adjustments Timing LegendData Label Information Data LabelSerial Number Manual Reset HI-LIMIT Instructions P O R TA N TP O RTA N T ADC 113000 9-11/23/05-0

ML-55HS specifications

The American Dryer Corp ML-55HS is a high-performance hand dryer that offers efficient and effective drying solutions for commercial and public restrooms. Known for its innovative design and advanced technology, the ML-55HS is a popular choice among facility managers looking for a reliable and eco-friendly drying option.

One of the key features of the ML-55HS is its powerful motor. With a speed of up to 28,000 RPM, this hand dryer can dry hands in as little as 10 to 15 seconds, significantly reducing wait times in busy facilities. This high speed also helps to minimize energy consumption, making the dryer not only time-efficient but also cost-effective.

The dryer is equipped with a built-in HEPA filter that captures 99.97% of airborne particles down to 0.3 microns. This means that users can enjoy not only the convenience of a fast-drying hand-drying solution but also a hygienic one, preventing the spread of germs and bacteria in shared spaces. The HEPA filter is easy to replace, ensuring ongoing efficiency and cleanliness.

Another notable aspect of the ML-55HS is its adjustable speed and heat settings. This versatility allows users to customize their drying experience based on their preferences, ensuring optimal comfort for everyone—regardless of the season or environment. Such adaptability also helps to further conserve energy.

The design of the ML-55HS is both sleek and durable, made from high-quality materials that can withstand the rigors of daily use in high-traffic areas. Its vandal-resistant features, including a tamper-proof cover and concealed screws, ensure that the dryer maintains its integrity even in challenging environments.

Moreover, the ML-55HS operates quietly, making it suitable for environments where noise reduction is a priority. Its low sound levels contribute to an overall pleasant restroom experience for users, promoting peace and comfort.

With an array of finishes available, the machine can seamlessly blend into various restroom designs while providing an eco-friendly alternative to traditional paper towels. The ML-55HS not only enhances user experience but also supports sustainability efforts by significantly reducing paper waste.

In conclusion, the American Dryer Corp ML-55HS brings together speed, efficiency, hygiene, and durability in a compact design, making it an excellent choice for any facility aiming to improve their restroom's functionality while catering to modern demands.
Top Page Image Contents