Humminbird 47, 531338-1_A manual Sonar Menu Tab, 3D Bottom Style, 3D Frame Style, Beam Select

Page 20

M47_Man_Eng_531338-1_A.qxd 12/13/2004 12:36 PM Page 38

Sonar Menu Tab

Press the MENU key twice to access the Main Menu System and then press the RIGHT 4-WAY Cursor Control key to select the Sonar tab.

Sonar Menu

3D Bottom Style

3D Bottom Style selects the bottom style used in the 3D Sonar View.

To change the 3D Bottom Style setting:

1.Highlight 3D Bottom Style on the Sonar main menu.

2.Use the LEFT or RIGHT 4-WAY Cursor Control keys to change the 3D Bottom Style setting. (Grid Only, Shaded with Grid, Shaded, Default = Shaded with Grid)

3D Frame Style

3D Frame Style selects the frame style used in the 3D Sonar View.

To change the 3D Frame Style setting:

1.Highlight 3D Frame Style on the Sonar main menu.

2.Use the LEFT or RIGHT 4-WAY Cursor Control keys to change the 3D Frame Style setting. (Simple, 2, 3, 4, Complex, Default = 3)

Beam Select

Beam Select sets which sonar returns from the transducer will be displayed on the screen.

When Beam Select is set to 455 kHz, the returns from the 455 kHz narrow beams will be displayed in all views, and the maximum depth capability of your unit will be 240 ft (75 m).

When the depth is greater than 240 ft (75 m), Beam Select should be set to 83 kHz. The unit will continue to acquire sonar returns below 240 ft and will be displayed in the 2D Sonar View.

NOTE: It is important to re-set Beam Select to 455 kHz when returning to water shallower than 240 ft (75 m) for maximum performance in the 3D views.

To change Beam Select:

1.Highlight Beam Select on the Sonar main menu.

2.Use the LEFT or RIGHT 4-WAY Cursor Control keys to select either the 455 kHz beam or the 83kHz beam. (455 kHz, 83 kHz, Default = 455 kHz)

33

34

Page 19 Page 21
Image 20
Page 19 Page 21
Contents Matrix 47 Operations Manual Table of Contents Thank YouAlarms Menu Tab Setup Menu TabViews Menu Tab Accessories Menu Tab Troubleshooting Sonar Menu Tab2D Sonar How Sonar Works3D Sonar Temperature water surface temperature What’s On the Display 3D ViewWhat’s On the Display 2D View Below the cursor3D Sonar View Views3D Sonar View 3D/2D Sonar Combo View Beam Sonar View3D/2D Sonar Combo View Beam Sonar View2D Sonar View 2D Sonar ViewReal Time Sonar RTS Window 2D Zoom View 2D Big Digits View2D Big Digits View 2D Zoom ViewBottom Presentation POWER/LIGHT Key Key FunctionsView Key Menu KeyAccessory Bus Powering Up the UnitMenu System Matrix 47 3D Title ScreenStart-Up Options Menu Normal OperationSelf Test Accessory Test SimulatorSystem Status PC Connect3D Lower Range Sonar X-Press Menu3D Bottom Zoom Reset View 3D History2D Sonar Window Beam SensitivityTo adjust the Upper Range To adjust the Lower RangeUpper Range Lower RangeZoom Level Chart SpeedBottom View Sonar Menu Tab 3D Bottom Style3D Frame Style Beam SelectFish ID 3D Reference Fish ID+Fish Sensitivity To change the RTS Window setting To change the Depth Lines settingDepth Lines Highlight RTS Window on the Sonar main menuSurface Clutter Noise FilterMax Depth Water TypeAlarms Menu Tab Depth AlarmFish ID Alarm To change the Depth Alarm settingLow Battery Alarm Alarm ToneSetup Menu Tab To change the Low Battery Alarm settingUser Mode Units DepthUnits Temp Units DistanceSelect Readouts Triplog ResetRestore Defaults Speed Calibration Depth OffsetTemp Offset Nmea Output Views Menu TabFollowing Nmea sentences are output To turn Nmea Output on or offAccessories Menu Tab TroubleshootingNegative terminal or ground Fuse is operationalDisplay Problems Problem Possible CauseControl head loses power at high speeds Finding the Cause of NoiseMatrix Fishing System Accessories SpecificationsContact Humminbird
Top Page Image Contents