Humminbird GR16 manual Access Under Mounting Location

Page 10

NOTE: Leave the NMEA pigtail secured to the cable unless needed in	#6 - 1/4” Mounting
order to make it easier to remove the GPS Receiver.	Screws

4. Route GPS Receiver cable through the stem and continue with the planned cable route.

5. Attach the GPS Receiver to its base using the included #6 - 1/4” screws. Hand tighten only.

Stem

CableStop

Route

Access Under Mounting Location

Follow these steps to deck mount the GPS receiver when you can route the cable down through the mounting surface:

1.Determine the best location, then test route the 20’ (6 m) cable from the Fishfinder control head to the planned mounting location of the GPS Receiver.

NOTE: 10’ extension cables may be purchased from Humminbird® if your planned cable route exceeds 20’ (6 m). Maximum cable length, including extension cables, should not exceed 50’ (16 m). Visit our website at www.humminbird.com, or call our Customer Resource Center at 1-800-633-1468 to purchase extension cables.

Attaching the Receiver to

the Base, Making Sure Cable is Not Pinched

Access Under

Mounting Location

2.Mark the mounting location and drill a 3/4” (19 mm) hole for the cable and cable connector. Secure the NMEA pigtail to the cable with electrical tape. Route the cable.

3.Cover the cable hole with the GPS Receiver. Make sure the Receiver is flush against the surface and mark the two mounting holes with a pencil or awl.

4.Move the Receiver to the side and drill two pilot holes, using a 5/32” (4 mm) bit.

NOTE: Apply marine-grade silicone caulk or sealant to both screw and drilled holes as needed to protect your boat from water damage.

5.Align the GPS Receiver’s screw holes over the pilot screw holes and attach with the #6 - 3/4” Phillips head screws. Hand tighten only.

NOTE: If the mounting surface is thin or made of a light-weight material, you may need to add reinforcing material below the mounting surface in order to support the GPS Receiver.

5

Image 10

Contents GR16 GPS Receiver Accessory Manual Thank You Table of Contents Alarms Menu Tab Troubleshooting GR16 GPS Connection Kit How GPS and Trackplotting WorkConnecting a GR16 GPS Receiver to the Fishfinder Nmea Output No access under mounting location GPS Receiver InstallationAccess under mounting location Shown in the illustrationAccess Under Mounting Location No Access Under Mounting Location Navigation views ViewsBird’s Eye View Bird’s Eye View Track View Combo ViewTrack View Track View with Active CursorCombo View View OrientationIntroduction to Navigation Waypoints, Routes and TracksSave, Edit, or Delete a Waypoint Navigate to a Waypoint or Position Add a Waypoint Target or Trolling Grid Track View with TargetSave or Clear a Current Track Edit, Delete or Hide Saved TracksMenu System MenuSonar Tab, Normal Mode Sonar Tab, Advanced Mode Normal Operation Start-Up Options MenuSimulator System Status Self TestAccessory Test GPS Diagnostic ViewExit PC Connect mode by powering the Fishing System off PC ConnectSonar X-Press Menu Sonar Views onlyTo Cancel Navigation Cancel NavigationOnly when Navigating MarkNavigation X-Press Menu Navigation Views onlyTo Zoom ZoomGo To To Begin NavigationTo view the Waypoint Name Submenu Waypoint NameOnly with an active cursor on a waypoint Highlight WaypointName on the Navigation X-Press menuSave Current Track Chart or Combo view onlyCursor to Waypoint Clear Current TrackTo Skip Next Waypoint Skip Next WaypointRemove Target Only if a Target is ActiveOnly if a Grid is Active Remove GridSonar Window Combo View onlyWaypoint Name Submenu Navigation Menu Tab Current Track Saved TracksHighlight Waypoints on the Navigation main menu WaypointsTo view the Waypoints Submenu Waypoints Submenu contains the following menu choicesTo change the Grid Rotation setting To change the View Orientation settingTo change the North Reference setting North ReferenceTrackpoint Interval To change the Trackpoint Interval settingTo change the Track Minimum Distance setting Track Min DistanceCourse Projection Line Map DatumDelete All Nav Data Alarms Menu Tab To change the Off Course Alarm setting Off Course AlarmArrival Alarm To change the Arrival Alarm settingTo change the Drift Alarm setting Drift AlarmHighlight Drift Alarm on the Alarms main menu Setup Menu Tab To Reset Triplog To change the Units Distance settingTo change the Units Speed setting Units DistanceDaylight Saving Time To change the Daylight Saving Time settingLocal Time Zone To change the Local Time ZoneTime Format To change the Position Format settingPosition Format Advanced, International onlyTo change the Date Format Date FormatNmea Output Following Nmea sentences are outputTo turn Nmea Output on or off Troubleshooting Fishing System Doesn’t Power UpHigh speeds Display ProblemsProblem Possible Cause Input voltage does not exceed 20 VoltsBoat’s engine Finding the Cause of NoisePossible Source of Noise Isolation Other electronic devices PropellerHumminbird Accessories GPS & Navigation Glossary Page Page Page Page Page Contact Humminbird Monday Friday 800 a.m. to 430 p.m. Central Standard Time