Humminbird 737 GPS manual Lat/Lon Grid, Spot Soundings, Set Simulation Position, Set Map Offset

Page 41

www..reelschel531438-1 A - 737_EnglishOnlymatic.qxd 9/25/2005..com7:53 PM Page 80

Lat/Lon Grid

Lat/Lon Grid allows you to display or hide a grid showing latitude and longitude lines.

To change the Lat/Lon Grid setting:

1.Highlight Lat/Lon Grid on the Chart main menu.

2.Use the LEFT or RIGHT 4-WAY Cursor Control keys to change the Lat/Lon Grid setting. (Hidden, Visible, Default = Hidden)

Spot Soundings

Spot Soundings allows you to display or hide spot soundings, which are depth measurements shown on the chart.

NOTE: Spot Soundings are only available with optional-purchase MMC/SD cards.

To change the Spot Soundings setting:

1.Highlight Spot Soundings on the Chart main menu.

2.Use the LEFT or RIGHT 4-WAY Cursor Control keys to change the Spot Soundings setting. (Hidden, Visible, Default = Hidden)

Set Simulation Position

(Advanced)

Set Simulation Position allows you to set the position of the boat used in the Simulator. The Set Simulation Position menu choice is only available when User Mode is set to Advanced (see Setup Menu Tab: User Mode).

To set the Simulation Position:

1.Activate the cursor and move it to the coordinates from where you want the simulation to start.

NOTE: The cursor must be active in order for this procedure to work.

2.Make sure you are in Advanced User Mode, then highlight Set Simulation Position on the Chart main menu.

3.Use the RIGHT 4-WAY Cursor Control key to change the Simulation Position setting. A confirmation dialog box will appear to allow you to change your mind, or to confirm your choice. If the cursor was not active before you began this procedure, you will see an error message. Exit the menu, set the cursor, then try again.

Set Map Offset

(Advanced)

Set Map Offset allows you to change the map offset used by the 700 Series™. The Set Map Offset menu choice is only available when User Mode is set to Advanced (see Setup Menu Tab: User Mode).

NOTE: The Map Offset will be applied to all maps and not just the map that requires the correction. The Map Offset should be cleared if a different map is to be used.

To change the Map Offset setting:

1. Activate the cursor and move it to the location where the Map Offset will be applied.

NOTE: The cursor must be active in order for this procedure to work.

2.Make sure you are in Advanced User Mode, then highlight Set Map Offset on the Chart main menu.

3.Use the RIGHT 4-WAY Cursor Control key to set the Map Offset. A confirmation dialog box will appear to allow you to change your mind, or to confirm your choice. If the cursor was not active before you began this procedure, you will see an error message. Exit the menu, set the cursor, then try again.

Clear Map Offset

(Advanced)

Clear Map Offset allows you to clear the Map Offset. The Clear map Offset menu choice is only available when User Mode is set to Advanced (see Setup Menu Tab: User Mode) and a Map Offset is currently active.

To Clear Map Offset:

1.Make sure you are in Advanced User Mode, then highlight Clear Map Offset on the Chart main menu.

2.Use the RIGHT 4-WAY Cursor Control key to clear the Map Offset.

73

74

Page 40 Page 42
Image 41
Page 40 Page 42
Contents Atic Thank You Table of ContentsKey Functions Views Menu Tab Accessories Menu Tab How Sonar Works Peak to Peak measures power output at the highest pointsDualBeam Plus Sonar QuadraBeam SonarWideSide Sonar With optional-purchase WideSide transducerHow GPS and Cartography Work Software UpdatesMulti-Media Card MMC/SD Slot With optional-purchase GPS ReceiverSoft Bottom RTS Real Time Sonar Window 83 kHz, Wide Beam Hollow Fish SymbolWhat’s On the Display Sonar views ViewsSonar View Real Time Sonar RTS Window Understanding Sonar HistoryBottom Presentation Freeze FrameSonar Zoom View Sonar Zoom ViewBig Digits View 200/83 kHz Split Sonar ViewCircular Flasher View Big Digits View 200/83 kHz Split Sonar ViewSide Beam View Screen Snapshot ViewMaking a Screen Snapshot Screen Capture ViewBird’s Eye View WideSide ViewChart View with Active Cursor Chart View without Active CursorCombo View DepthWaypoints, Routes and Tracks Viewing CartographySave, Edit, or Delete a Waypoint Add a Waypoint Target or Trolling Grid Chart View with GridKey Functions POWER/LIGHT KeyView Key Info KeyWAY Cursor Control Key Accessory BusMark Key Goto KeyPresence or absence of a transducer Powering Up the UnitMenu System Normal Operation Start-Up Options MenuSystem Status SimulatorGPS Diagnostic View Accessory TestExit PC Connect mode by powering the Fishing System off Sonar X-PressTMMenu To adjust the SideSide WideSide transducer WideSide view onlyTo adjust the Upper Range To adjust the SensitivitySensitivity Upper RangeSide Beam Range Chart SpeedLower Range Bottom View Cancel NavigationBottom Range Bottom LockWaypoint Name Navigation X-PressTM MenuOnly with an active cursor on a waypoint To view the Waypoint Name SubmenuSave Current Track Cursor to WaypointClear Current Track Save Current RouteSonar Window Remove TargetRemove Grid Delete Image Screen Snapshot X-Press TM MenuDelete All Images Sonar Menu TabFish ID+TM Beam SelectTo use Beam Select Highlight Beam Select on the Sonar main menuZoom Width Fish ID SensitivityKHz Sensitivity AdvancedWideSide Sensitivity KHz BalanceDepth Lines Advanced with WideSide transducerMax Depth Surface ClutterNoise Filter Water Type To change the Water Type settingTransducer Select Navigation Menu TabWaypoints Current TrackSaved Tracks Routes Chart OrientationNorth Reference Grid RotationMap Datum Track Min DistanceCourse Projection Line Export All Nav DataChart Detail Level Chart Menu TabMap Borders With optional-purchase GPS Receiver onlySpot Soundings Lat/Lon GridSet Simulation Position Set Map OffsetDepth Alarm Alarms Menu TabFish ID Alarm To change the Depth Alarm settingTemp Alarm Low Battery AlarmOff Course Alarm Arrival AlarmAlarm Tone Drift AlarmSetup Menu Tab To change the Drift Alarm settingUnits Depth User ModeUnits Temp Units DistanceRestore Defaults Triplog ResetSelect Readouts Advanced, Sonar view onlyTemp Offset Depth OffsetSpeed Calibration Position FormatDate Format Time FormatNmea Output SonarUsing Screen Snapshot Accessories Menu TabViews Menu Tab To Change the View Status of Any ViewTo view screen snapshots TroubleshootingTo make a screen snapshot Screen Snapshot must be enabled Finding the Cause of Noise Display ProblemsSpecifications Series Fishing System AccessoriesSonar Terms Glossary100 102 Receiver See Transmitter104 GPS & Navigation Terms 108 Contact Humminbird
Top Page Image Contents