Humminbird 141c manual Start-Up Options Menu, Normal Operation, Simulator

Page 12

531442-1_A_141c_Eng.qxd 11/15/2005 8:39 PM Page 22

Start-Up Options Menu

Press the MENU key when the Title screen is displayed to access the Start-Up Options menu.

Use the UP or DOWN 4-WAY Cursor keys to position the cursor, then the RIGHT Cursor key to select one of the following choices. If you wait too long, the system will default to whichever menu mode happens to be highlighted:

• Normal

• Simulator

• System Status.

Start-Up Options Menu

See the following paragraphs for more information about each of these choices.

Normal Operation

Use Normal operation for on the water operation with a transducer connected. In addition, your 100 Series™ Fishing System uses advanced transducer detection methods to determine if a transducer is connected. If a functioning transducer is connected, Normal operation will be selected automatically at power up and your Fishing System can be used on the water.

Exit Normal operation by powering your Fishing System off.

Simulator

Use the Simulator to learn how to use your 100 Series™ Fishing System before taking your boat on the water. The Simulator is a very powerful tool that simulates on the water operation, providing a randomly-updated display. We recommend going through this manual while using the Simulator, since all of the menus function and affect the display the way they actually do when in Normal operation.

NOTE: To get the full benefit of the Simulator, it is important to select Simulator manually from the Start-Up Options menu as opposed to letting the Fishing System enter Simulator automatically (as it will if a transducer is not connected and you do nothing during power up). Manually selecting Simulator from the Start-Up Options menu allows you to pre- configure your 100 Series™ Fishing System for on the water operation. Any menu changes you make will be saved for later use.

A message will appear on the display periodically to remind you that you are using the Simulator.

Exit the Simulator by powering your Fishing

System off.

Simulator

17

18

Page 11 Page 13
Image 12
Page 11 Page 13
Contents 141c Operations Manual Table of Contents Thank YouTable of Contents Peak to Peak measures power output at the highest points How Sonar WorksSingle Beam Sonar What’s On the Display High Sonar Intensity Return Bait BallViews Sonar ViewSonar View Zoom View Big Digits View Circular Flasher View Sonar ViewUnderstanding Sonar History Real Time Sonar RTS WindowBottom Presentation Sonar Zoom View Sonar Zoom ViewPOWER/LIGHT Key Big Digits ViewKey Functions Circular Flasher ViewMenu Key WAY Cursor Control KeyExit Key Owering Up the UnitSonar Tab, Normal Mode Sonar Tab, Advanced Mode Menu SystemPress TM Menu Start-Up Options Menu Normal OperationSimulator Accessory Test System Status Sonar X-Press TM MenuConduct a unit self-test StatusTo adjust the Sensitivity To adjust the Upper RangeSensitivity Upper RangeChart Speed Lower RangeZoom Level To adjust the Bottom Range Bottom LockBottom Range Sonar Menu TabTo change the Fish ID Sensitivity setting To change the RTS Window settingFish ID+TM Fish ID SensitivityBottom View Zoom WidthDepth Lines Surface Clutter Noise FilterMax Depth Alarms Menu Tab To change the Water Type settingAlarms Menu Water TypeDepth Alarm Fish ID AlarmLow Battery Alarm Temp AlarmAlarm Tone Setup Menu TabTo change the Alarm Tone setting Highlight Alarm Tone on the Alarms main menuUser Mode Units DepthUnits Temp Units DistanceTriplog Reset Restore DefaultsSelect Views Select Readouts Depth OffsetTemp Offset Troubleshooting To change the Speed Calibration settingSpeed Calibration Advanced, with Temp/Speed onlyDisplay Problems Problem Possible CauseControl head loses power at high speeds Finding the Cause of NoiseSpecifications GlossarySonar Terms 531442-1A141cEng.qxd 11/15/2005 840 PM Receiver See Transmitter 531442-1A141cEng.qxd 11/15/2005 840 PM 531442-1A141cEng.qxd 11/15/2005 840 PM Contact Humminbird
Top Page Image Contents